SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHONDA2002CIVIC SIREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 67 (FUEL AND EMISSIONS SYSTEMS)SYMPTOM TROUBLESHOOTING INDEX
2002 Honda Civic Si

Symptom Troubleshooting Index

2002 Honda Civic SiSECTION Symptom Troubleshooting Index
WARNING: This page is about a different car, the 2006 Acura MDX, 2005 Acura MDX, 2004 Acura MDX, and 2003 Acura MDX. However, it is still accessible from the selected car via links, so may be relevant.

When the vehicle has one of these symptoms, check for a diagnostic trouble code (DTC) with the HDS. If there is no DTC, do the diagnostic procedure for the symptom, in the sequence listed, until you find the cause.

SYMPTOM TROUBLESHOOTING INDEX

Symptom Diagnostic procedure Also check for
Engine will not start (MIL works OK, no DTCs set)
  1. Test the battery (see BATTERY TEST ).
  2. Test the starter (see STARTER CIRCUIT TROUBLESHOOTING ).
  3. Check the fuel pressure (see FUEL PRESSURE TEST ).
  4. Troubleshoot the fuel pump circuit (see FUEL PUMP CIRCUIT TROUBLESHOOTING ).
  • Low compression
  • No ignition spark
  • Intake air leaks
  • Locked up engine
  • Broken timing belt
  • Contaminated fuel
Engine will not start (MIL comes on and stays on, or never comes on at all, no DTCs set) Troubleshoot the MIL circuit (see MIL CIRCUIT TROUBLESHOOTING ).  
Engine will not start (immobilizer indicator stays on or flashes) Troubleshoot the immobilizer system (see TROUBLESHOOTING ).  
Engine starts but stalls immediately (MIL works OK, no DTCs set) Troubleshoot the immobilizer system (see TROUBLESHOOTING ).  
Engine is hard to start (MIL works OK, no DTCs set)
  1. Test the battery (see BATTERY TEST ).
  2. Check the fuel pressure (see FUEL PRESSURE TEST ).
  3. Clean the throttle body (see THROTTLE BODY CLEANING ).
  • Low compression
  • Intake air leaks
  • Contaminated fuel
  • Weak spark
Cold fast idle too low (MIL works OK, no DTCs set)
  1. Do the PCM idle learn procedure (see PCM IDLE LEARN PROCEDURE ).
  2. Check the idle speed (see IDLE SPEED INSPECTION ).
  3. Clean the throttle body (see THROTTLE BODY TEST ).
  
Cold fast idle too high (MIL works OK, no DTCs set)
  1. Do the PCM idle learn procedure (see PCM IDLE LEARN PROCEDURE ).
  2. Check the idle speed (see IDLE SPEED INSPECTION ).
  3. Inspect/adjust the throttle cable (see THROTTLE CABLE REMOVAL/INSTALLATION ).
  4. Do the throttle position learning check (see THROTTLE POSITION LEARNING CHECK ).
  
Idle speed fluctuates (MIL works OK, no DTCs set)
  1. Do the PCM idle learn procedure (see PCM IDLE LEARN PROCEDURE ).
  2. Check the idle speed (see IDLE SPEED INSPECTION ).
  3. Inspect/adjust the throttle cable (see THROTTLE CABLE ADJUSTMENT ).
  4. Do the carbon accumulation check (see CARBON ACCUMULATION CHECK ).
 Intake vacuum leaks
After warming up, idle speed is below specification without load (MIL works OK, no DTCs set)
  1. Troubleshoot the alternator FR signal circuit (see ALTERNATOR FR SIGNAL CIRCUIT TROUBLESHOOTING ).
  2. Do the carbon accumulation check (see THROTTLE BODY TEST ).
  
After warming up, idle speed is above specification without load (MIL works OK, no DTCs set)
  1. Inspect/adjust the throttle cable (see THROTTLE CABLE ADJUSTMENT ).
  2. Troubleshoot the alternator FR signal circuit (see ALTERNATOR FR SIGNAL CIRCUIT TROUBLESHOOTING ).
  
Low power (MIL works OK, no DTCs set)
  1. Check the fuel pressure (see FUEL PRESSURE TEST ).
  2. Inspect/adjust the throttle cable (see THROTTLE CABLE ADJUSTMENT ).
  • Low compression
  • Incorrect camshaft timing
  • Incorrect engine oil level
Engine stalls (MIL works OK, no DTCs set)
  1. Do the PCM idle learn procedure (see PCM IDLE LEARN PROCEDURE ).
  2. Check the fuel pressure (see FUEL PRESSURE TEST ).
  3. Check the idle speed (see IDLE SPEED INSPECTION ).
  4. Troubleshoot the brake pedal position switch signal circuit (see BRAKE PEDAL POSITION SWITCH SIGNAL CIRCUIT TROUBLESHOOTING ).
  • Intake air leaks
  • Faulty harness and sensor connections
Difficult to refuel (MIL works OK, no DTCs set)
  1. Check the fuel vent tube between the EVAP canister and the fuel tank.
  2. Check the fuel tank vapor recirculation tube between the fuel pipe and the fuel tank.
  3. Check the fuel tank signal tube between the fuel pipe and the fuel tank (2003-2004 models).
  4. Replace the fuel tank (see FUEL TANK REPLACEMENT ).
 Malfunctioning gas station filling nozzle.
Fuel overflows during refueling (No DTCs set) Replace the fuel tank (see FUEL TANK REPLACEMENT ). Malfunctioning gas station filling nozzle.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.