Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedures
2004 Oldsmobile Bravada RWDSECTION Diagnostic Procedures
WARNING: This page is about a different car, the 2002 Pontiac Grand Am, 2002 Oldsmobile Alero, 2002 Chevrolet Monte Carlo, and 2002 Chevrolet Impala. However, it is still accessible from the selected car via links, so may be relevant.
- Perform diagnostic system check - engine controls. See DIAGNOSTIC SYSTEM CHECK - ENGINE CONTROLS under SELF-DIAGNOSTIC SYSTEM. After performing diagnostic system check - engine controls, go to next step.
- Attempt to start the engine. Does the engine start and run? If yes, go to step 4. If no, go to next step.
- Observe the Freeze Frame/Failure Records for this DTC. Turn ignition off for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running the DTC or within the parameters observed in the Freeze Frame/Failure Records. See CONDITIONS FOR RUNNING DTC . Does the DTC fail this ignition? If yes, go to next step. If no, see DIAGNOSTIC AIDS .
- Turn ignition off. Disconnect the 6-way ignition control module connector. Remove the injector fuse. Turn ignition on, with engine off. Momentarily probe the 3X reference signal circuit at the ignition module harness connector with a test light connected to B+. Observe the Engine Speed parameter with a scan tool. Is an Engine Speed displayed? If yes, go to step 8. If no, go to next step.
- Did the test light illuminate? If yes, go to step 7. If no, go to next step.
- Turn ignition off. Disconnect the PCM. Turn ignition on, with engine off. Test the 3X reference circuit of the ignition control module for an open or a short to voltage. Did you find and correct the condition? If yes, go to step 12. If no, go to step 9.
- Turn ignition off. Disconnect the PCM. Test the 3X reference circuit of the ignition control module for a short to ground. Did you find and correct the condition? If yes, go to step 12. If no, go to step 9.
- Test for an intermittent and for a poor connection at the ignition control module. Did you find and correct the condition? If yes, go to step 12. If no, go to step 10.
- Test for an intermittent and for a poor connection at the PCM. Did you find and correct the condition? If yes, go to step 12. If no, go to step 11.
- Replace ignition control module. After repairs, go to step 12.
- Replace PCM. Perform PCM relearn procedure. See POWERTRAIN CONTROL MODULE under PROGRAMMING. After replacing PCM, go to next step.
- Clear the DTCs with a scan tool. Turn ignition off for 30 seconds. Start the engine. Operate the vehicle within the conditions for Running the DTC. See CONDITIONS FOR RUNNING DTC . Does the DTC run and pass? If yes, go to next step. If no, go to step 2.
- Using scan tool, observe stored information and Capture Info. Does the scan tool display any DTCs that you have not diagnosed? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS . If no, system is okay.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.