SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 106 (ENGINE CONTROLS SELF-DIAGNOSTICS - 6.5L)INSPECTION/MAINTENANCE PROCEDURESINSPECTION/MAINTENANCE COMPONENT MONITORING SYSTEM SET PROCEDUREPROCEDURES
2004 Oldsmobile Bravada AWD

Inspection/Maintenance Component Monitoring System Set Procedure: Procedures

2004 Oldsmobile Bravada AWDSECTION Procedures
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2002 GMC Savana Special, 2002 GMC Savana Camper Special, 2002 GMC Savana, 2002 Chevrolet RV Cutaway, and 2002 Chevrolet Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
  1. Did you perform the Inspection/Maintenance (I/M) System Check? If yes, go to next step. If no, see INSPECTION/MAINTENANCE SYSTEM CHECK  .
    2. CAUTION: Road test a vehicle under safe conditions and while obeying all traffic laws. Do not attempt any maneuvers that could jeopardize vehicle control. Failure to adhere to these precautions could lead to serious personal injury and vehicle damage.
  2. Ensure the vehicle is within the Conditions for Running specified in the supporting text. Turn OFF all of the accessories (e.g., A/C, blower fan, etc.). Start the engine, and allow the engine to idle for 2 minutes. In order for this test to run, the vehicle must operate in the following conditions:
    • Acceleration at part throttle to 50 MPH with this speed maintained until the engine reaches operating temperature. This may be up to 8-10 minutes depending on the start up coolant temperature.
    • Continue the operating conditions for an additional 3 minutes after the engine reaches operating temperature.
    • After the specified time has elapsed, vehicle requires acceleration at 75 percent throttle until a speed of 68 MPH is attained.

    With a scan tool, review the I/M System Status display. Did the Component Monitoring System Status update to YES? If yes, go to step  5 . If no, go to next step.

  3. With a scan tool, observe the DTC Information. Does the scan tool indicate any failed DTCs? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS  . If no, go to next step.
  4. To determine which DTCs are required to run in order to complete this test, see INSPECTION/MAINTENANCE SYSTEM DTCS  table. With a scan tool, observe the Not Ran Since Code Cleared display. Determine which of the DTCs required for a YES status has not run. Enter the DTC number in the Specific DTC menu of the scan tool. Operate the vehicle within the Conditions for Running DTC. Repeat the procedure until the scan tool indicates the diagnostic test has run. Repeat procedure for any additional required DTCs that have not run. With a scan tool, observe the I/M System Status display. Did the Component Monitoring System Status update to YES? If yes, go to next step. If no, see DIAGNOSTIC AIDS  .
  5. With a scan tool, observe the Emission Related DTC portion of the I/M System Status display. Does the scan tool indicate any Emission Related DTCs set? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS  . If no, system is okay.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.