Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSVOLKSWAGEN2013BEETLE R-LINE, 2.0L ENG VIN TREPAIR AND DIAGNOSIS (SINGLE PAGE)EXTERNAL PAGESDIFFERENT CARSECTION 1557 (CLIMATE CONTROL SYSTEM)GENERAL SPECIFICATIONS
2013 Volkswagen Beetle R-Line, 2.0L Eng VIN T
General Specifications
2013 Volkswagen Beetle R-Line, 2.0L Eng VIN TSECTION General Specifications
WARNING: This page is about a different car, the 2011 Mercury Milan, 2011 Lincoln MKZ, and 2011 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
GENERAL SPECIFICATIONS
| Item | Specification |
|---|---|
| A/C Compressor Oil | |
|
NOTE:
Use of any A/C compressor oil other than what is specified for the specific vehicle configuration will damage the A/C compressor and contaminate the refrigerant system. For non-hybrid vehicles with a pulley driven (conventional) A/C compressor, PAG Refrigerant Compressor Oil only must be used. For hybrid vehicles with an electric A/C compressor, Motorcraft® Electric A/C Compressor Oil must be used.
|
|
MATERIAL SPECIFICATIONS
| Item | Specification | Fill Capacity |
|---|---|---|
| Motorcraft® Electric A/C Compressor Oil YN-32 |
- | Hybrid vehicles only 130 ml (4.4 fl oz) |
| Motorcraft® PAG Refrigerant Compressor Oil YN-12-D |
WSH-M1C231-B | Non-hybrid vehicles only 177 ml (6 fl oz) |
| Motorcraft® R-134a Refrigerant YN-19 (US); CYN-16-R (Canada) |
WSH-M17B19-A | 0.62 kg (22 oz) (1.38 lb) |
GENERAL SPECIFICATIONS
| Item | Specification |
|---|---|
| Magnetic Clutch | |
| Air gap between pulley and clutch disc | 0.3-0.6 mm (0.012-0.024 in) |
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| A/C compressor bolts | 25 | 18 | - |
| A/C compressor bracket bolts | 25 | 18 | - |
| A/C compressor clutch disc and hub bolt | 14 | - | 124 |
| A/C compressor discharge fitting nut (hybrid) | 15 | - | 133 |
| A/C compressor manifold bolt | 15 | - | 133 |
| A/C compressor nut | 25 | 18 | - |
| A/C compressor stud | 9 | - | 80 |
| A/C compressor suction fitting nut (hybrid) | 15 | - | 133 |
| A/C pressure relief valve | 10 | - | 89 |
| A/C pressure transducer | 10 | - | 89 |
| Auxiliary coolant flow pump bracket bolts | 25 | 18 | - |
| Compressor manifold and tube suction fitting nut | 15 | - | 133 |
| Condenser fitting nut (inlet and outlet) | 15 | - | 133 |
| Condenser-to-evaporator line fitting nut | 15 | - | 133 |
| Evaporator outlet line fitting nut | 15 | - | 133 |
| Evaporator-to-compressor suction line bracket bolt | 6 | - | 53 |
| Heater core and evaporator core housing nuts | 9 | - | 80 |
| High-pressure Schrader-type valve | 2.5 | - | 22 |
| High-pressure service gauge port valve cap | 0.8 | - | 7 |
| Low-pressure Schrader-type valve | 1.8 | - | 16 |
| Low-pressure service gauge port valve cap | 0.8 | - | 7 |
| Radiator bracket bolts | 10 | - | 89 |
| Thermostatic Expansion Valve (TXV) fitting nut | 15 | - | 133 |
| TXV manifold and tube bracket bolt | 8 | - | 71 |
| Washer reservoir filler neck bolt | 6 | - | 53 |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.