Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSVOLKSWAGEN2013BEETLE BASE, 2D HATCHBACK, 2.5L ENG VIN X, AUTOMATIC TRANSREPAIR AND DIAGNOSISENGINE PERFORMANCEIGNITION SYSTEM2.5L - GENERIC SCAN TOOL - ENGINE CODE(S): CBTA & CBUA (HATCHBACK)
2013 Volkswagen Beetle Base, 2D Hatchback, 2.5L Eng VIN X, Automatic Trans
2.5L - Generic Scan Tool - Engine Code(S): CBTA & CBUA (Hatchback)
2013 Volkswagen Beetle Base, 2D Hatchback, 2.5L Eng VIN X, Automatic TransSECTION 2.5L - Generic Scan Tool - Engine Code(S): CBTA & CBUA (Hatchback)
- St Generic Scan Tool
- General Information
- Description And Operation
- Diagnosis And Testing
- Preliminary Check
- Readiness Code
- Diagnostic Modes 01 - 09
- Notes
- Diagnostic Mode 01 - Read Current System Data
- Diagnostic Mode 02 - Read Operating Conditions
- Diagnostic Mode 03 - Read DTC Memory
- Diagnostic Mode 04 - Erase DTC Memory
- Diagnostic Mode 06 - Read Test Results For Specific Diagnostic Functions
- Notes
- Test Requirements
- Work Procedure
- Monitor-ID 01: Oxygen Sensor Monitor Bank 1 - Sensor 1
- Monitor-ID 02: Oxygen Sensor Monitor Bank 1 - Sensor 2
- Monitor-ID 03: Oxygen Sensor Monitor Bank 1- Sensor 3 (CBUA Only)
- Monitor-ID 21: Oxygen Storage Content of Catalyst
- Monitor-ID 35: Variable Valve Timing Monitor
- Monitor-ID 3B: Fuel Tank EVAP System Integrity/Leak Test (0.40)
- Monitor-ID 3C: Fuel Tank EVAP System Integrity/Small Leak Test (0.20)
- Monitor-ID 3D: EVAP Purge Flow Monitor
- Monitor-ID 41: Oxygen Sensor Heater Monitor Bank 1 - Sensor 1
- Monitor-ID 42: Oxygen Sensor Heater Monitor Bank 1 - Sensor 2
- Monitor-ID 43: Oxygen Sensor Heater Monitor Bank 1 - Sensor 3 (CBUA Only)
- Monitor-ID 71: Secondary Air Monitor (CBUA Only)
- Monitor-ID A2: Misfire Cylinder 1 Data
- Monitor-ID A3: Mis-Fire Cylinder 2 Data
- Monitor-ID A4: Mis-Fire Cylinder 3 Data
- Monitor-ID A5: Mis-Fire Cylinder 4 Data
- Monitor-ID A6: Mis-Fire Cylinder 5 Data
- Diagnostic Mode 07 - Read Faults Detected During The Current Or Last Driving Cycle
- Diagnostic Mode 08 - Request Control Of On-Board System, Test Or Component
- Diagnostic Mode 09 - Read Vehicle Information
- Engine DTC Tables
- Transmission DTC Tables
- Diagnostic Procedures
- Fuel Pump Voltage Supply, Checking
- Fuel Pump Pressure, Checking
- Fuel Pump Delivery Rate, Checking
- EVAP System, Checking For Leaks
- EVAP Purge Regulator Valve, Checking
- Leak Detection Pump, Checking
- Accelerator Pedal Position Sensor -G79- /Accelerator Pedal Position Sensor 2 -G185-, Checking
- Throttle Valve Control Module -J338-, Checking
- Oxygen Sensor Before Catalytic Converter, Checking
- Heated Oxygen Sensor -G39-, Checking Heater
- Oxygen Sensor In Center Catalytic Converter, Checking (CBUA Only)
- Oxygen Sensor In Bank 1 Center Three Way Catalytic Converter -G465-, Checking Heater
- Oxygen Sensor After Three Way Catalytic Converter -G130-, Checking
- Oxygen Sensor After Three Way Catalytic Converter -G130-, Checking Heater
- Manifold Absolute Pressure Sensor -G71-, Checking
- Engine Coolant Temperature Sensor -G62- / Engine Coolant Temperature Sensor On Radiator Outlet -G83-, Checking
- Outside Air Temperature Sensor -G17-, Checking
- Manifold Absolute Pressure Sensor -G71- / Intake Air Temperature Sensor -G42-, CHECKING
- Engine Speed Sensor -G28-, Checking
- Fuel Injectors, Checking
- ECM Voltage Supply, Checking
- Catalytic Converter, Checking
- Secondary Air Injection Combination Valve, Checking
- Secondary Air Injection Pump Motor -V101-, Checking
- Secondary Air Injection Pump Relay -J299-, Checking
- Secondary Air Injection Solenoid Valve -N112-, Checking
- Secondary Air Injection Sensor 1 -G609-, Checking
- Camshaft Position Sensor -G40-, Checking
- Camshaft Adjustment Valve 1 -N205-, Checking
- Knock Sensor 1 -G61- / Knock Sensor 2 -G66-, Checking
- Ignition Coil With Power Output Stage, Checking
- Speed Signal, Checking
- CAN BUS Terminal Resistance, Checking
- CAN-BUS Terminal Resistance, Transmission Control Module To Engine Control Module, Checking
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.