Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSVOLKSWAGEN2010GOLF (5K1) L5-2.5L (CBTA)REPAIR AND DIAGNOSISRELAYS AND MODULESRELAYS AND MODULES - RESTRAINTS AND SAFETY SYSTEMSAIR BAG CONTROL MODULESERVICE AND REPAIR
2010 Volkswagen Golf (5K1) L5-2.5L (CBTA)
Air Bag Control Module: Service and Repair
2010 Volkswagen Golf (5K1) L5-2.5L (CBTA)SECTION Service and Repair
9
Airbag Control Module J234
When working on the airbag control module always not the safety guidelines when working on airbags, belt tensioners and battery cut-out units. Refer to => [ Airbag, Belt Tensioner and Battery Cut-Out Units, General Safety Precautions ] Airbag, Belt Tensioner and Battery Cut-Out Units, General Safety Precautions.
Removing
- Disconnect the battery.
- Remove right and left footwell trim from center console (other center console components do not need to be removed):
• Basic: => [ Center Console, Basis, Golf from MY 09 ] Center Console, Basis, Golf From MY 09
• Highline: => [ Center Console, Highline, Golf from MY 09 ] Center Console, Highline, Golf From MY 09
• For clarity, center console is not depicted in the illustration.
- Open locking mechanism of connector - 1 - and disconnect wiring harness from control module - 2 -.
- Remove three nuts - 3 - (9 Nm).
- Remove the control module from the vehicle.
Installing
- Install in reverse order of removal.
- Switch on ignition.
Make sure that no persons are in the vehicle.
- Connect the battery.
- If the control unit was replaced, it must be coded. Adapting components (coding). Refer to => [ Components, Adapting ] Components, Adapting
Airbag Control Module J234
When working on the airbag control module always not the safety guidelines when working on airbags, belt tensioners and battery cut-out units. Refer to => [ Airbag, Belt Tensioner and Battery Cut-Out Units, General Safety Precautions ] Airbag, Belt Tensioner and Battery Cut-Out Units, General Safety Precautions.
Removing
- Disconnect the battery.
- Remove right and left footwell trim from center console (other center console components do not need to be removed):
• Basic: => [ Center Console, Basis, Golf from MY 09 ] Center Console, Basis, Golf From MY 09
• Highline: => [ Center Console, Highline, Golf from MY 09 ] Center Console, Highline, Golf From MY 09
• For clarity, center console is not depicted in the illustration.
- Open locking mechanism of connector - 1 - and disconnect wiring harness from control module - 2 -.
- Remove three nuts - 3 - (9 Nm).
- Remove the control module from the vehicle.
Installing
- Install in reverse order of removal.
- Switch on ignition.
Make sure that no persons are in the vehicle.
- Connect the battery.
- If the control unit was replaced, it must be coded. Adapting components (coding). Refer to => [ Components, Adapting ] Components, Adapting
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.