SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2025SEQUOIA CAPSTONEREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 68 (NAVIGATION SYSTEM - SERVICE INFORMATION)MULTI-DISPLAYREMOVAL [09/2014 - 11/2017]PROCEDURE
2025 Toyota Sequoia Capstone

Removal [09/2014 - 11/2017]: Procedure

2025 Toyota Sequoia CapstoneSECTION Procedure
WARNING: This page does not describe the selected car, but rather 21 other vehicles, including the 2024 Lexus RC 350, 2024 Lexus RC 300, 2023 Lexus RC 350, 2023 Lexus RC 300, and 2022 Lexus RC 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Refer to PRECAUTION [09/2014 - 11/2017]

  2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column) 

    Refer to PROCEDURE - Step 2

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [09/2014 - 10/2015] , or refer to INITIALIZATION [10/2015 - 11/2017]

  4. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 9

  5. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 10

  6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 11

  7. REMOVE METER HOOD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 14

  8. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 30

  9. REMOVE MULTI-DISPLAY ASSEMBLY WITH BRACKET 
    1. Remove the 2 bolts.
      GTY501119Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Pull the multi-display assembly with bracket as shown in the illustration to disengage the 4 clips.
      GTY501177Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect each connector.
      GTY501178Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disengage the clamp and remove the multi-display assembly with bracket.
  10. REMOVE NO. 1 MULTI-DISPLAY BRACKET 
    1. Remove the 2 screws and No. 1 multi-display bracket.
      GTY465053Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE MULTI-DISPLAY ASSEMBLY 
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.