Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Installation [03/2023 - ]: Procedure
- ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
- INSTALL STEERING COLUMN ASSEMBLY NOTE:HINT: As the illustration shown is an example, the actual details may differ.
Make sure that the wire harness is not interfering with the steering column assembly.
- INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
- CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
- INSTALL COLUMN HOLE COVER SILENCER SHEET
- INSTALL NO. 1 AIR DUCT
Torque: 9.8 N.m (100 kgf/cm, 87 in.lbf)
- INSTALL FRONT NO. 1 CONSOLE BOX INSERT
- INSTALL NO. 2 KNEE PROTECTOR BRACKET (w/o Knee Airbag)
Torque: 10 N.m (102 kgf/cm, 7 ft.lbf)
- INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
Refer to PROCEDURE - Step 1 - INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Refer to PROCEDURE - Step 28 [12/2022 - 09/2023] , or refer to PROCEDURE - Step 28 [09/2023 - ]
- INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL
- INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
- INSTALL COWL SIDE TRIM BOARD LH
- INSTALL FRONT DOOR SCUFF PLATE LH
- INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY NOTE:HINT: As the illustration shown is an example, the actual details may differ.
- Do not remove/install the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch ON.
- Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the ignition switch ON.
- Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
*a Clamp - - - Using pliers, expand the clamp.
- While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.
- Return the clamp to its original position.
- Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
- INSTALL UPPER STEERING COLUMN COVER
- INSTALL LOWER STEERING COLUMN COVER
- ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
- INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Refer to PROCEDURE - Step 7 - INSTALL STEERING WHEEL ASSEMBLY
Refer to INSTALLATION [12/2022 - ]
- UPDATE ECU SECURITY KEY
Refer to UPDATE ECU SECURITY KEY [12/2022 - ]
HINT:
After replacing the power steering ECU assembly, make sure to perform update ECU security key.
- ECU CONFIGURATION
Refer to ECU CONFIGURATION [12/2022 - ]
HINT:
After replacing the power steering ECU assembly, make sure to perform ECU configuration.
- PERFORM POWER STEERING ECU INITIAL SETTING (TORQUE SENSOR ZERO POINT CALIBRATION AND ASSIST MAP WRITING)
- PERFORM END POSITION INITIAL SETTING
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.