Rear Power Window RH does not Operate with Rear Power Window Switch RH [11/2022 - ]: Procedure

1. Operate the power window regulator switch assembly and check that the front passenger door power window operates normally.

   OK

   Operates normally

   Result

   Proceed to
   OK
   NG

Result: 

OK 

USE SIMULATION METHOD TO CHECK 

Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2021 - ]

Result: 

NG 

See step  2

1. Read the Data List according to the display on the GTS.

   Body Electrical > Main Body > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   RR Door Power Window UP Switch	Rear RH door power window manual up switch	OFF or ON	OFF: Manual up switch not being operated ON: Manual up switch being operated	-
   RR Door Power Window DOWN Switch	Rear RH door power window manual down switch	OFF or ON	OFF: Manual down switch not being operated ON: Manual down switch being operated	-

   Body Electrical > Main Body > Data List 

   Tester Display
   RR Door Power Window UP Switch
   RR Door Power Window DOWN Switch

   OK

   On the GTS screen, ON or OFF is displayed accordingly.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  7

Result: 

OK 

See step  3

1. Check that the power window components of the rear RH door window are correctly installed (components which may cause the door glass to deviate from the normal fully closed position, such as the door glass runs).

   OK

   The power window components of the rear RH door window are correctly installed.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

INSTALL PARTS CORRECTLY 

Result: 

OK 

See step  4

1. Remove the bolt of the door glass and check that the door glass slides smoothly without being caught when it is moved up and down by hand.
   NOTE:

   • The door glass fits with the glass run without improper contact or deformation.
   • Foreign matter is not caught in the glass run.
   • The glass run is not misaligned.
   • The door belt moulding or door inner glass weatherstrip is not caught.
   • The glass is not tilted and does not catch.

   OK

   The door glass slides smoothly without being caught when it is moved up and down by hand.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

INSTALL PARTS CORRECTLY (Remove any foreign matter which may cause poor installation, or repair or replace parts that are installed incorrectly.) 

Result: 

OK 

See step  5

1. Remove the rear door glass sub-assembly (for rear RH door).

   HINT: 

   Refer to DISASSEMBLY [11/2022 - ]

2. Connect the multiplex network master switch assembly connector.
3. Turn the ignition switch to ON.
4. Operate the rear power window regulator switch assembly (for RH door) and check that the front door window regulator with motor assembly (for rear RH door) operates smoothly.

   OK

   Operates smoothly without being caught.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (OVERHEATED POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door) WAS DEFECTIVE) 

Result: 

NG 

See step  6

1. Remove the rear door window regulator with motor assembly (for rear RH door).

   HINT: 

   Refer to DISASSEMBLY [11/2022 - ]

2. Remove the power window regulator motor assembly (for rear RH door).

   HINT: 

   Refer to REMOVAL [11/2022 - ]

3. Check that the rear door window regulator sub-assembly RH is not deformed or distorted.

   OK

   No deformation or distortion.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door) 

Refer to REMOVAL [11/2022 - ]

Result: 

NG 

REPLACE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (for Rear RH Door) 

Refer to DISASSEMBLY [11/2022 - ]

Refer to INSPECTION [09/2021 - ]

Result

Result: 

NG 

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH Door) 

Refer to REMOVAL [09/2021 - ]

Result: 

OK 

See step  8

1. Disconnect the M2 power window regulator motor assembly (for rear RH door) connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   M2-10 (UP) - M3-5 (UP)	Always	Below 1 Ω
   M2-7 (DOWN) - M3-4 (DOWN)	Always	Below 1 Ω
   M2-10 (UP) or M3-5 (UP) - Body ground	Always	10 kΩ or higher
   M2-7 (DOWN) or M3-4 (DOWN) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door) 

Refer to REMOVAL [11/2022 - ]

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR