Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch [09/2021 - 11/2022]: Procedure
- READ VALUE USING GTS (Master Switch)
- Read the Data List according to the display on the GTS.
Body Electrical > Master Switch > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note D Door P/W Auto SW Driver door power window auto switch signal OFF or ON OFF: Driver door power window auto up or auto down switch not being operated
ON: Driver door power window auto up or auto down switch being operated- Body Electrical > Master Switch > Data List
Tester Display D Door P/W Auto SW OK
On the GTS screen, ON or OFF is displayed accordingly.
Result
Proceed to OK NG
Result:
NG
REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY. Refer to REMOVAL [09/2021 - ]
Result:
OK
See step 2
- Read the Data List according to the display on the GTS.
- READ VALUE USING GTS (D-Door Motor)
- Read the Data List according to the display on the GTS.
Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note D Door P/W Auto SW Driver door power window auto switch signal OFF or ON OFF: Driver door power window auto up or auto down switch not being operated
ON: Driver door power window auto up or auto down switch being operated- Body Electrical > D-Door Motor > Data List
Tester Display D Door P/W Auto SW OK
On the GTS screen, ON or OFF is displayed accordingly.
Result
Proceed to OK NG
Result:
NG
See step 5
Result:
OK
See step 3
- Read the Data List according to the display on the GTS.
- PERFORM INITIALIZATION (for Driver Door)
- Initialize the power window regulator motor assembly (for driver door).
Refer to INITIALIZATION [09/2021 - ]
Result
Proceed to NEXT
Result:
NEXT
See step 4
- Initialize the power window regulator motor assembly (for driver door).
- CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
- Check that the driver door power window moves when the auto up and down functions of the multiplex network master switch assembly are operated.
Refer to OPERATION CHECK [09/2021 - ]
OK
Driver door auto up and down functions are normal.
Result
Proceed to OK NG
Result:
OK
END (PROBLEM DUE TO INITIALIZATION FAILURE)
Result:
NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door). Refer to REMOVAL [09/2021 - 11/2022]
- Check that the driver door power window moves when the auto up and down functions of the multiplex network master switch assembly are operated.
- REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
- Replace the multiplex network master switch assembly.
Refer to REMOVAL [09/2021 - ]
Result
Proceed to NEXT
Result:
NEXT
See step 6
- Replace the multiplex network master switch assembly.
- CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
- Check that the driver door power window moves when the auto up and down functions of the multiplex network master switch assembly are operated.
Refer to OPERATION CHECK [09/2021 - ]
OK
Driver door auto up and down functions are normal.
Result
Proceed to OK NG
Result:
OK
END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)
Result:
NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door). Refer to REMOVAL [09/2021 - 11/2022]
- Check that the driver door power window moves when the auto up and down functions of the multiplex network master switch assembly are operated.
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.