Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
On-Vehicle Inspection [12/2024 - ]: Procedure
- INSPECT NO. 1 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI MAIN NO. 1)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition Result 3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ 3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω If the result is not as specified, replace the No. 1 electronic fuel injection main relay (EFI MAIN NO. 1).
- Measure the resistance according to the value(s) in the table below.
- INSPECT NO. 2 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI MAIN NO. 2)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition Result 3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ 3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω If the result is not as specified, replace the No. 2 electronic fuel injection main relay (EFI MAIN NO. 2).
- Measure the resistance according to the value(s) in the table below.
- INSPECT NO. 3 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI MAIN NO. 3)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition Result 3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ 3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω If the result is not as specified, replace the No. 3 electronic fuel injection main relay (EFI MAIN NO. 3).
- Measure the resistance according to the value(s) in the table below.
- INSPECT ELECTRONIC DRIVER UNIT RELAY (EDU)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition Result 3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ 3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω If the result is not as specified, replace the electronic driver unit relay (EDU).
- Measure the resistance according to the value(s) in the table below.
- INSPECT INJECTOR RELAY (IGT/INJ MAIN)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition Result 3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ 3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω If the result is not as specified, replace the injector relay (IGT/INJ MAIN).
- Measure the resistance according to the value(s) in the table below.
- INSPECT IGP RELAY (IGP NO. 1)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition Result 3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ 3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω If the result is not as specified, replace the IGP relay (IGP NO. 1).
- Measure the resistance according to the value(s) in the table below.
- INSPECT NO. 2 IGP RELAY (IGP NO. 2)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition Result 3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ 3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω If the result is not as specified, replace the No. 2 IGP relay (IGP NO. 2).
- Measure the resistance according to the value(s) in the table below.
- INSPECT NO. 3 IGP RELAY (IGR NO. 3)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition Result 3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ 3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω If the result is not as specified, replace the No. 3 IGP relay (IGR NO. 3).
- Measure the resistance according to the value(s) in the table below.
- INSPECT NO. 4 IGP RELAY (IGR NO. 4)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition Result 3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ 3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω If the result is not as specified, replace the No. 4 IGP relay (IGR NO. 4).
- Measure the resistance according to the value(s) in the table below.
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.