Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2010OUTBACK SPORT F4-2.5L SOHCREPAIR AND DIAGNOSISTECHNICAL SERVICE BULLETINSCUSTOMER INTERESTNAVIGATION SYSTEM - SOFTWARE UPDATE FOR BUTTONS INOP.
2010 Subaru Outback Sport F4-2.5L SOHC
Navigation System - Software Update For Buttons Inop.
2010 Subaru Outback Sport F4-2.5L SOHCSECTION Navigation System - Software Update For Buttons Inop.
NUMBER: 15-144-10
DATE: 10/12/10
APPLICABILITY:
2010MY early production
2011MY Legacy and Outback w/ Navigation and Rear View Camera
SUBJECT:
Navigation System Update
Update Disc KUMA 832-10-007
Legacy/Outback Version 6500
INTRODUCTION
The purpose of this bulletin is to provide the instructions for updating the Navigation Operating Software using the Navigation Program Update Disc. This update is for the operating system only and does not update the map data in any way. The updated software will address the following issue. The navigation operation buttons "Map" "Dest" "Menu" and "Info" are inoperative. The issue will only occur once on initial start up during one drive cycle, if the transmission gear selector (auto or manual) is put in reverse and taken out very quickly.
COUNTERMEASURE IN PRODUCTION
The updated software was used in production starting mid-September, 2010.
PARTS
The Navigation Program Update Disc will be sent to all dealers the week of October 11, 2010. The previously released updates are all included in this version.
Note:
Should you require an additional Navigation Program Update Disc, it can be ordered through parts, Part # S0A635087.
REPAIR PROCEDURE/INFORMATION
Note:
If at any time the (+) positive or (-) negative battery cable is disconnected; the update procedure will need to be performed AGAIN going forward.
1) Turn ignition switch to the "ON" position.
2) Eject Map Disc from Navigation unit.
^ Screen will read "Please insert the Map Disc".
3) Load the Navigation Update Disc.
^ Screen will go blank for a moment.
^ Screen will read "System loading. Don't turn off the power"
^ After completion of update, screen will go blank, push agree button.
^ Screen will read "Disc is not a Map Disc".
4) Eject Navigation Update Disc.
^ Screen will read "Disc is not a MAP DVD".
5) Insert the Map Disc.
The Program Update process has been completed.
WARRANTY/CLAIM INFORMATION
DATE: 10/12/10
APPLICABILITY:
2010MY early production
2011MY Legacy and Outback w/ Navigation and Rear View Camera
SUBJECT:
Navigation System Update
Update Disc KUMA 832-10-007
Legacy/Outback Version 6500
INTRODUCTION
The purpose of this bulletin is to provide the instructions for updating the Navigation Operating Software using the Navigation Program Update Disc. This update is for the operating system only and does not update the map data in any way. The updated software will address the following issue. The navigation operation buttons "Map" "Dest" "Menu" and "Info" are inoperative. The issue will only occur once on initial start up during one drive cycle, if the transmission gear selector (auto or manual) is put in reverse and taken out very quickly.
COUNTERMEASURE IN PRODUCTION
The updated software was used in production starting mid-September, 2010.
PARTS
The Navigation Program Update Disc will be sent to all dealers the week of October 11, 2010. The previously released updates are all included in this version.
Note:
Should you require an additional Navigation Program Update Disc, it can be ordered through parts, Part # S0A635087.
REPAIR PROCEDURE/INFORMATION
Note:
If at any time the (+) positive or (-) negative battery cable is disconnected; the update procedure will need to be performed AGAIN going forward.
1) Turn ignition switch to the "ON" position.
2) Eject Map Disc from Navigation unit.
^ Screen will read "Please insert the Map Disc".
3) Load the Navigation Update Disc.
^ Screen will go blank for a moment.
^ Screen will read "System loading. Don't turn off the power"
^ After completion of update, screen will go blank, push agree button.
^ Screen will read "Disc is not a Map Disc".
4) Eject Navigation Update Disc.
^ Screen will read "Disc is not a MAP DVD".
5) Insert the Map Disc.
The Program Update process has been completed.
WARRANTY/CLAIM INFORMATION
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.