Electronic Brake Control Module (EBCM) X1

2008 Pontiac Grand Prix BaseSECTION Electronic Brake Control Module (EBCM) X1
WARNING: This page is about a different car, the 2008 Buick LaCrosse and 2008 Buick Allure. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Electronic Brake Control Module (EBCM) X1 Connector End View
GM684893Courtesy of GENERAL MOTORS CORP.
Electronic Brake Control Module (EBCM) X1

Pin Wire Circuit Function
1 0.35 BN/WH 2086 Yaw Rate Sensor Test Control (JL4/JL9)
2 0.35 BN 882 Right Rear Wheel Speed Sensor Signal
3 0.35 WH 883 Right Rear Wheel Speed Sensor Low Reference
4 0.35 D-GN 872 Right Front Wheel Speed Sensor Signal
5 0.35 TN 833 Right Front Wheel Speed Sensor Low Reference
6 0.5 WH 17 Stop Lamp Switch Signal
7 0.35 WH 121 Engine Speed Signal (LY7)
8 0.8 PK 1039 Ignition 1 Voltage
9 0.35 TN/BK 464 Delivered Torque Signal (NW7)
10 0.35 L-BU 715 Lateral Accelerometer Signal (JL4/JL9)
11 0.35 WH 121 Engine Speed Signal (L26 w/JL9)
11 0.35 TN 2501 High Speed GMLAN Serial Data Bus (-) (LY7 w/JL9)
12 3 BK/WH 251 Ground
13 3 RD 1442 Battery Positive Voltage
14 3 OG 1740 Battery Positive Voltage
15 3 BK/WH 251 Ground
16 0.35 GY 930 5-Volt Reference (JL4/JL9)
17 0.35 OG 1575 Brake Pressure Sensor Signal (JL4/JL9)
18 0.35 GY/BK 1798 Ground (JL4/JL9)
19 0.35 TN/WH 2500 High Speed GMLAN Serial Data Bus (+) (JL4/JL9)
20 0.35 L-BU 830 Left Front Wheel Speed Sensor Signal
21 0.35 YE 873 Left Front Wheel Speed Sensor Low Reference
22 0.35 BK 884 Left Rear Wheel Speed Sensor Signal
23 0.35 RD 885 Left Rear Wheel Speed Sensor Low Reference
24 - - Not Used
25 0.35 L-BU 1122 ABS/TCS Class 2 Serial Data
26 0.35 D-BU 716 Yaw Rate Sensor Signal (JL4/JL9)
27 0.35 OG/BK 463 Requested Torque Signal (NW7)
28 0.35 GY 596 5-Volt Reference (JL4/JL9)
29 0.8 BN 1295 Variable Effort Steering Actuator Control (NV8)
30 0.8 WH 1294 Variable Effort Steering Actuator Supply Voltage (NV8)
Connector Part Information 
  • OEM: 15326390
  • Service: 12167314
  • Description: 30-Way F GT 150, 280 Mixed Series Sealed (BK)
Terminal Part Information 
  • Pins: 12- 15
  • Terminal/Tray: 15304720/19
  • Core/Insulation Crimp: 4/5
  • Release Tool/Test Probe: 15315247/J-35616-4A (PU)
  • Pins: 1-7, 9-11, 16-23, 25-30
  • Terminal/Tray: 12191819/8
  • Core/Insulation Crimp: Pins 1-7, 9-11, 16-23, 25-28 - E/A
  • Core/Insulation Crimp: Pins 8, 29, 30- 2/A
  • Release Tool/Test Probe: 15315247/J-35616-2A (GY)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.