Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC2008GRAND PRIX BASEREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 309 (ENGINE MECHANICAL)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2008 Pontiac Grand Prix Base
Fastener Tightening Specifications
2008 Pontiac Grand Prix BaseSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2008 Hummer H2. However, it is still accessible from the selected car via links, so may be relevant.
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Accessory Drive Belt Idler Pulley Bolt | 50 N.m | 37 lb ft |
| Accessory Drive Belt Tensioner Bolts | 50 N.m | 37 lb ft |
| Active Fuel Management Oil Pressure Relief Valve | 27 N.m | 20 lb ft |
| Air Conditioning Drive Belt Tensioner Bolts | 50 N.m | 37 lb ft |
| Automatic Transmission Flex Plate Bolts - First Pass | 20 N.m | 15 lb ft |
| Automatic Transmission Flex Plate Bolts - Second Pass | 50 N.m | 37 lb ft |
| Automatic Transmission Flex Plate Bolts - Final Pass | 100 N.m | 74 lb ft |
| Battery Cable Channel Bolt | 12 N.m | 106 lb in |
| Camshaft Position (CMP) Actuator Magnet Bolts | 12 N.m | 106 lb in |
| Camshaft Position (CMP) Actuator Solenoid Valve - First Pass | 65 N.m | 48 lb ft |
| Camshaft Position (CMP) Actuator Solenoid Valve - Final Pass | 90 degrees | |
| Camshaft Position (CMP) Sensor Bolt | 12 N.m | 106 lb in |
| Camshaft Position (CMP) Sensor Wire Harness Bolt | 12 N.m | 106 lb ft |
| Camshaft Retainer Bolts - Hex Head Bolts | 25 N.m | 18 lb ft |
| Camshaft Retainer Bolts - TORX Head Bolts | 15 N.m | 11 lb ft |
| Camshaft Sprocket Bolt - First Pass | 75 N.m | 55 lb ft |
| Camshaft Sprocket Bolt - Final Pass | 50 degrees | |
| Connecting Rod Bolts - First Pass | 20 N.m | 15 lb ft |
| Connecting Rod Bolts - Final Pass | 85 degrees | |
| Coolant Air Bleed Pipe and Cover Bolts | 12 N.m | 106 lb in |
| Coolant Temperature Sensor | 20 N.m | 15 lb ft |
| Crankshaft Balancer Bolt - Installation Pass - to Ensure the Balancer is Completely Installed | 330 N.m | 240 lb ft |
| Crankshaft Balancer Bolt - First Pass - Install a NEW Bolt After the Installation Pass and Tighten as Described in the First and Final Passes | 50 N.m | 37 lb ft |
| Crankshaft Balancer Bolt - Final Pass | 140 degrees | |
| Crankshaft Bearing Cap M8 Bolts | 25 N.m | 18 lb ft |
| Crankshaft Bearing Cap M10 Bolts - First Pass in Sequence | 20 N.m | 15 lb ft |
| Crankshaft Bearing Cap M10 Bolts - Final Pass in Sequence | 80 degrees | |
| Crankshaft Bearing Cap M10 Studs - First Pass in Sequence | 20 N.m | 15 lb ft |
| Crankshaft Bearing Cap M10 Studs - Final Pass in Sequence | 51 degrees | |
| Crankshaft Oil Deflector Nuts | 25 N.m | 18 lb ft |
| Crankshaft Position (CKP) Sensor Bolt | 25 N.m | 18 lb ft |
| Crankshaft Rear Oil Seal Housing Bolts | 30 N.m | 22 lb ft |
| Cylinder Head M8 Bolts - in Sequence | 30 N.m | 22 lb ft |
| Cylinder Head M11 Bolts - First Pass in Sequence | 30 N.m | 22 lb ft |
| Cylinder Head M11 Bolts - Second Pass in Sequence | 90 degrees | |
| Cylinder Head M11 Bolts - Final Pass in Sequence | 70 degrees | |
| Cylinder Head Plug | 20 N.m | 15 lb ft |
| Engine Block Coolant Drain Hole Plug | 60 N.m | 44 lb ft |
| Engine Block Coolant Heater | 50 N.m | 37 lb ft |
| Engine Block Oil Gallery Plugs | 60 N.m | 44 lb ft |
| Exhaust Manifold Bolts - First Pass | 15 N.m | 11 lb ft |
| Exhaust Manifold Bolts - Final Pass | 20 N.m | 15 lb ft |
| Exhaust Manifold Heat Shield Bolts | 9 N.m | 80 lb in |
| Exhaust Manifold Studs | 20 N.m | 15 lb ft |
| Front Cover Bolts | 25 N.m | 18 lb ft |
| Fuel Injection Fuel Rail Bolts | 10 N.m | 89 lb in |
| Fuel Injection Fuel Rail Crossover Tube Bolts | 3.8 N.m | 34 lb in |
| Fuel Rail Stop Bracket Bolt | 50 N.m | 37 lb ft |
| Generator Bracket Bolts | 50 N.m | 37 lb ft |
| Ignition Coil Bracket-to-Valve Rocker Arm Cover Studs | 12 N.m | 106 lb in |
| Ignition Coil-to-Bracket Bolts | 10 N.m | 89 lb in |
| Intake Manifold Bolts - First Pass in Sequence | 5 N.m | 44 lb in |
| Intake Manifold Bolts - Final Pass in Sequence | 10 N.m | 89 lb in |
| Intake Manifold Sight Shield Retainer Bolts | 5 N.m | 44 lb in |
| J 41798 M8 Bolt | 25 N.m | 18 lb ft |
| J 41798 M10 Bolts | 50 N.m | 37 lb ft |
| Knock Sensor Bolts | 25 N.m | 18 lb ft |
| Oil Filter | 30 N.m | 22 lb ft |
| Oil Filter Fitting | 55 N.m | 40 lb ft |
| Oil Level Indicator Switch | 20 N.m | 15 lb ft |
| Oil Level Indicator Tube Bolt | 25 N.m | 18 lb ft |
| Oil Pan Baffle Bolts | 9 N.m | 80 lb in |
| Oil Pan Closeout Cover Bolt - Left Side | 9 N.m | 80 lb in |
| Oil Pan Closeout Cover Bolt - Right Side | 9 N.m | 80 lb in |
| Oil Pan Cover Bolts | 9 N.m | 80 lb in |
| Oil Pan Drain Plug | 25 N.m | 18 lb ft |
| Oil Pan M6 Bolts - Oil Pan-to-Rear Housing | 12 N.m | 106 lb in |
| Oil Pan M8 Bolts - Oil Pan-to-Engine Block and Oil Pan-to-Front Cover | 25 N.m | 18 lb ft |
| Oil Pressure Sensor | 35 N.m | 26 lb ft |
| Oil Pump Cover Bolts | 12 N.m | 106 lb in |
| Oil Pump Relief Valve Plug | 12 N.m | 106 lb in |
| Oil Pump Screen Nuts | 25 N.m | 18 lb ft |
| Oil Pump Screen-to-Oil Pump Bolts | 12 N.m | 106 lb in |
| Oil Pump-to-Engine Block Bolts | 25 N.m | 18 lb ft |
| Power Steering Pump-to-Engine Block Bolts | 50 N.m | 37 lb ft |
| Spark Plugs | 15 N.m | 11 lb ft |
| Throttle Body Bolts | 10 N.m | 89 lb in |
| Throttle Body Nuts | 10 N.m | 89 lb in |
| Throttle Body Studs | 6 N.m | 53 lb in |
| Timing Chain Tensioner Bolts | 25 N.m | 18 lb ft |
| Valley Cover Bolts | 25 N.m | 18 lb ft |
| Valve Lifter Guide Bolts | 12 N.m | 106 lb in |
| Valve Rocker Arm Bolts | 30 N.m | 22 lb ft |
| Valve Rocker Arm Cover Bolts | 12 N.m | 106 lb in |
| Water Inlet Housing Bolts | 15 N.m | 11 lb ft |
| Water Pump Bolts - First Pass | 15 N.m | 11 lb ft |
| Water Pump Bolts - Final Pass | 30 N.m | 22 lb ft |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.