Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Mechanical Inspection: Compression
Check engine mechanical condition with a compression gauge, vacuum gauge, or an engine analyzer. See 4-CYLINDER COMPRESSION SPECIFICATIONS and V6 COMPRESSION SPECIFICATIONS tables. See engine analyzer manual for specific instructions. Ensure battery is fully charged, engine is at normal operating temperature and throttle valve is fully open when checking the compression.
Remove Auto Shutdown (ASD) relay to prevent engine from starting when checking the compression. On all vehicles except Avenger and Sebring Coupe, ASD relay is located in Power Distribution Center (PDC). For relay location, check label on underside of PDC cover. On Avenger and Sebring Coupe, ASD relay is located behind driver's side strut tower at rear corner of engine compartment and contains a Gray 9-pin connector. See Figure . Once compression test is complete, reinstall ASD relay and use scan tool to clear Diagnostic Trouble Code (DTC) from Powertrain Control Module (PCM). See appropriate SELF-DIAGNOSTICS article for clearing of DTC.
On vehicles with Distributorless Ignition System (DIS), ensure electrical connector is disconnected from ignition coil to prevent engine from starting when performing compression test.
| Application | Specification | ||||
|---|---|---|---|---|---|
| Normal Compression Pressure | |||||
| Breeze, Cirrus & Stratus | |||||
| 2.0L & 2.4L | 170-225 psi (12-16 kg/cm2 ) | ||||
| Neon | |||||
| 2.0L DOHC & SOHC | 170-225 psi (12-16 kg/cm2 | ||||
| Minimum Compression Pressure | |||||
| Breeze, Cirrus & Stratus | |||||
| 2.0L & 2.4L | 100 psi (7 kg/cm2) | ||||
| Neon | |||||
| 2.0L SOHC | 100 psi (7 kg/cm2) | ||||
| Maximum Variation Between Cylinders | |||||
| All Models | (1) | ||||
|
|||||
| Application | Specification | |||||||
|---|---|---|---|---|---|---|---|---|
| Normal Compression Pressure | ||||||||
| Avenger, Cirrus, Sebring Convertible, Sebring Coupe & Stratus | ||||||||
| 2.5L | ||||||||
| Calif. Emission Vehicles | 154-202 psi (11-14 kg/cm2 ) | |||||||
| Except Calif. Emission Vehicles | 192-211 psi (13-15 kg/cm2 ) | |||||||
| Concorde, Intrepid, LHS & 300M | ||||||||
| 2.7L, 3.2L & 3.5L | (1) | |||||||
| Minimum Compression Pressure | ||||||||
| Avenger, Cirrus, Sebring Convertible, Sebring Coupe & Stratus | ||||||||
| 2.5L | 100 psi (7 kg/cm2 ) | |||||||
| Concorde, Intrepid, LHS & 300M | ||||||||
| 2.7L, 3.2L & 3.5L | 100 psi (7 kg/cm2 ) | |||||||
| Maximum Variation Between Cylinders | ||||||||
| Avenger, Cirrus, Sebring Convertible, Sebring Coupe & Stratus | ||||||||
| 2.5L | 14 psi (1 kg/cm2 ) | |||||||
| Concorde, Intrepid, LHS & 300M | ||||||||
| 2.7L, 3.2L & 3.5L | (2) | |||||||
|
||||||||
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.