Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 267 (ENGINE CONTROLS - REMOVAL & INSTALLATION)TORQUE SPECIFICATIONS
2004 Oldsmobile Bravada RWD
Torque Specifications
2004 Oldsmobile Bravada RWDSECTION Torque Specifications
WARNING: This page is about a different car, the 2003 Pontiac Grand Am and 2003 Oldsmobile Alero. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | |||
|---|---|---|---|---|
| Battery Terminal Nut-To-Starter | 13 (17) | |||
| Crankshaft Balancer Bolt | (1) | |||
| Engine Coolant Temperature Sensor (3.4L) | 15 (20) | |||
| Engine Fuel Pipe Fittings (3.4L) | 13 (17) | |||
| Engine Fuel Pipe Retainer Bolt (3.4L) | 18 (25) | |||
| Fuel Filter Fitting | 20 (27) | |||
| Fuel Pipe Fitting | 13 (17) | |||
| Fuel Rail Pipe Retainer Bolt | 18 (25) | |||
| Fuel Tank Strap Bolts | 26 (35) | |||
| HO2S 1 | 22 (30) | |||
| HO2S 2 | 30 (41) | |||
| Knock Sensor | ||||
| 2.2L | 18 (25) | |||
| 3.4L | 14 (19) | |||
| Oil Pressure Switch | 16 (22) | |||
| Power Steering Pump Mounting Bolts (3.4L) | 25 (34) | |||
| Power Steering Pump Pressure/Return Hose Fittings (3.4L) | 20 (27) | |||
| Spark Plug | ||||
| 2.2L | 15 (20) | |||
| 3.4L | 11 (15) | |||
| Starter Bolt | 30 (40) | |||
| Upper Intake Manifold Bolt | 18 (25) | |||
| Wheel Nuts | 100 (136) | |||
| INCH Lbs. (N.m) | ||||
| Accelerator/Cruise Control Cable Bracket Bolt | 89 (10) | |||
| Air Cleaner Duct Clamp | 44 (5) | |||
| Air Cleaner Element Cover Screw | 27 (3) | |||
| Air Cleaner Intake Duct Attaching Nut | 89 (10) | |||
| Air Cleaner Outlet Resonator Clamp | 44 (5) | |||
| Air Cleaner Outlet Resonator Mounting Bolt | 89 (10) | |||
| Battery Cable Bolt | 11 (15) | |||
| Camshaft Position Sensor Bolt | 71 (8) | |||
| Crankshaft Position Sensor Bolt (2.2L) | 71 (8) | |||
| Crankshaft Position Sensor Bolt (3.4L - 7X Sensor) | 97 (11) | |||
| Crankshaft Position Sensor Harness Retaining Clip Bolt (3.4L - 24X Sensor) | 89 (10) | |||
| ECT Sensor | 89 (10) | |||
| EVAP Canister Bolt | 89 (10) | |||
| EVAP Canister Purge Solenoid Bracket Nut | 71 (8) | |||
| Exhaust Heat Shield | ||||
| Bolt | 18 (2) | |||
| Nut | 9 (1) | |||
| Fuel Bundle Fasteners | 89 (10) | |||
| Fuel Filler Hose Clamp | 27 (3) | |||
| Fuel Filler Pipe Attaching Screw | 89 (10) | |||
| Fuel Pressure Regulator Screw | 44 (5) | |||
| Fuel Rail Pipe Fittings | 89 (10) | |||
| Fuel Rail Retaining Bolt/Stud | 89 (10) | |||
| Idle Air Control Valve Screw | 27 (3) | |||
| Ignition Coil Housing Screw | 35 (4) | |||
| Ignition Coil Mounting Screw (3.4L) | 40 (4.5) | |||
| Ignition Control Module Cover Bolt (2.2L) | 89 (10) | |||
| Ignition Control Module Retaining Screw | 13 (1.5) | |||
| MAP Sensor Screw | 27 (3) | |||
| PCM Connector Screw | 71 (8) | |||
| Power Steering Pump Pressure Hose Retainer Nut (3.4L) | 45 (5) | |||
| Power Steering Pump Return Hose Retainer Nut (3.4L) | 50 (37) | |||
| Radiator Drain Cock | 18 (2) | |||
| "S" Terminal Nut-To-Starter | 27 (3) | |||
| Throttle Body Retaining Bolt/Stud | 89 (10) | |||
| Throttle Position Sensor Mounting Screw | 18 (2) | |||
| Upper Air Cleaner Cover Screws | 27 (3) | |||
| Water Pump Drain Plug | 16 (22) | |||
|
||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.