Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Installation Procedure
2004 Oldsmobile Bravada RWDSECTION Installation Procedure
WARNING: This page is about a different car, the 2009 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
- Install the chassis fuel feed line (1) to the retainers.
- Install the brake, fuel and EVAP line bundle (1) to the vehicle.
- Install the brake, fuel and EVAP line retainers (1) to the underbody and side rail.
- Install the brake, fuel and EVAP line retainers (2) to the underbody studs.
- Install the brake line retainers (3) to the underbody side rail.
- Remove the caps from the brake pipe fittings.
- Install the rear brake pipe (2) fitting to the rear brake hose fitting (1).
Tighten: Tighten the fitting to 18 N.m (13 lb ft).
- Remove the caps from the brake pipe fittings.
- Install the rear brake pipe fitting (2) to the rear brake crossover pipe fitting (1).
Tighten: Tighten the fitting to 18 N.m (13 lb ft).
- Connect the chassis EVAP line quick connect fitting (1) to the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service .
- Connect the body wiring harness electrical connector (1) to the fuel pressure sensor.
- Install the fuel tank. Refer to Fuel Tank Replacement (AWD) or Fuel Tank Replacement (FWD) .
- Remove the caps and plugs from the brake pipe fittings and the BPMV outlet ports.
- Install the rear brake pipe fittings (1) to the BPMV.
Tighten: Tighten the fittings to 21 N.m (16 lb ft).
- Connect the chassis fuel feed line quick connect fitting (3) to the fuel rail. Refer to Metal Collar Quick Connect Fitting Service .
- Connect the chassis EVAP line quick connect fitting (2) to the EVAP canister purge solenoid valve. Refer to Plastic Collar Quick Connect Fitting Service .
- If equipped with LAT, install the engine coolant surge tank. Refer to Radiator Surge Tank Replacement .
- Install the underhood electrical center, non LAT equipped. Refer to Underhood Electrical Center or Junction Block Replacement (HP7) or Underhood Electrical Center or Junction Block Replacement (HP5) .
- Install the chassis fuel feed line clip (1) to the fuel line bracket.
- Install the intake manifold cover. Refer to Intake Manifold Cover Replacement .
- Install the air cleaner outlet duct. Refer to Air Cleaner Outlet Duct Replacement
- Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
- Use the following procedure in order to inspect for leaks:
- Turn the ignition ON, with the engine OFF, for 2 seconds.
- Turn the ignition OFF for 10 seconds.
- Turn the ignition ON, with the engine OFF.
- Inspect for fuel leaks.
CAUTION:
Refer to Fastener Caution
.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.