Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1787 (FRONT SUSPENSION SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2004 Oldsmobile Bravada RWD
Fastener Tightening Specifications
2004 Oldsmobile Bravada RWDSECTION Fastener Tightening Specifications
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2005 Isuzu Ascender, 2005 GMC Envoy XUV, 2005 GMC Envoy XL, 2005 GMC Envoy, and 2005 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Brake Hose Bracket Retaining Bolts | 10 N.m | 89 lb in |
| Drive Axle Nut | 140 N.m | 103 lb ft |
| Lower Ball Joint Retaining Nuts | 110 N.m | 81 lb ft |
| Lower Control Arm Bracket Front Mounting Bolt | 265 N.m | 195 lb ft |
| Lower Control Arm Bracket Rear Mounting Bolt | 240 N.m | 177 lb ft |
| Lower Control Arm to the Lower Control Arm Bracket Mounting Nuts | 110 N.m | 81 lb ft |
| Outer Tie Rod to the Steering Knuckle Retaining Nut | 45 N.m | 33 lb ft |
| Shock Absorber Retaining Nut | 45 N.m | 33 lb ft |
| Shock Module Upper Retaining Nuts | 45 N.m | 33 lb ft |
| Shock Module Yoke to the Lower Control Arm Retaining Nut | 110 N.m | 81 lb ft |
| Shock Module Yoke to the Shock Absorber Pinch Bolt | 70 N.m | 52 lb ft |
| Stabilizer Shaft Insulator Clamp Mounting Bolts | 55 N.m | 41 lb ft |
| Stabilizer Shaft Link Retaining Nuts | 145 N.m | 107 lb ft |
| Upper Ball Joint Pinch Bolt | 40 N.m | 30 lb ft |
| Upper Control Arm Mounting Bolts | 150 N.m | 111 lb ft |
| Wheel Hub and Bearing Mounting Bolts | 105 N.m | 77 lb ft |
| Wheel Speed Sensor to the Wheel Hub and Bearing Mounting Bolt | 18 N.m | 13 lb ft |
| Wheel Stud | 130 N.m | 95 lb ft |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.