Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1588 (BODY FRONT END)REPAIR INSTRUCTIONSFENDER REPLACEMENT-FRONT-LEFT (NEW STYLE CHEVROLET)INSTALLATION PROCEDURE

2004 Oldsmobile Bravada RWD

Installation Procedure

2004 Oldsmobile Bravada RWDSECTION Installation Procedure

WARNING: This page is about a different car, the 2003 GMC Sierra, 2003 GMC Cab & Chassis Sierra, 2003 Chevrolet Silverado, and 2003 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.

Position the fender to vehicle.
NOTE: Refer to FASTENER NOTICE .
Install the rear lower fender bolt.
Tighten

Tighten the rear lower fender bolt to 25 N.m (18 lb ft).

Fig 1: Installing Rear Lower Fender Bolt
Courtesy of GENERAL MOTORS CORP.
Install the fender to radiator support bolts and retainer.
Tighten

Tighten the radiator support bolts to 25 N.m (18 lb ft).

Fig 2: Installing Fender To Radiator Support Bolts
Courtesy of GENERAL MOTORS CORP.
Connect the left front grille clip to the fender.

Fig 3: Connecting Left Front Grille Clip To Fender
Courtesy of GENERAL MOTORS CORP.
Install the fender to door hinge bolts.
Tighten

Tighten the door hinge bolts to 25 N.m (18 lb ft).

Fig 4: Installing Fender To Door Hinge Bolts
Courtesy of GENERAL MOTORS CORP.
Install the fender to upper cowl bracket bolt.
Tighten

Tighten the upper cowl bracket bolts to 25 N.m (18 lb ft).

Fig 5: Installing Fender To Upper Cowl Bracket Bolt
Courtesy of GENERAL MOTORS CORP.
Install the push-in retainers (2) in order to attach the wheelhouse panel (1) to the fender (3).
Install the underhood electrical center. Refer to UNDERHOOD ELECTRICAL CENTER OR JUNCTION BLOCK REPLACEMENT .

Fig 6: Installing Push-In Retainers
Courtesy of GENERAL MOTORS CORP.
Connect the windshield washer hose to the clips on the fender.

Fig 7: Connecting Windshield Washer Hose To Clips On Fender
Courtesy of GENERAL MOTORS CORP.
Connect the hood latch release cable to the clips.
Install the battery tray. Refer to BATTERY TRAY REPLACEMENT .

Fig 8: Connecting Hood Latch Release Cable To Clips
Courtesy of GENERAL MOTORS CORP.
Install the wheelhouse panel bracket.
Tighten

Tighten the wheelhouse bracket nuts and bolts to 25 N.m (18 lb ft).

Fig 9: Installing Wheelhouse Panel Bracket
Courtesy of GENERAL MOTORS CORP.
Install the left fender to cowl support brace.
Tighten

Tighten the cowl support brace bolts to 9 N.m (80 lb in).
Install the left hood spring assembly.
Tighten

Tighten the hood spring bolt to 25 N.m (18 lb ft).
Install the hood. Refer to Hood Replacement .

Fig 10: Installing Left Fender To Cowl Support Brace
Courtesy of GENERAL MOTORS CORP.
Install the left outboard cowl vent grille trim piece.
Connect the negative battery cable. Refer to BATTERY NEGATIVE CABLE DISCONNECT/CONNECT PROCEDURE (SINGLE BATTERY) or BATTERY NEGATIVE CABLE DISCONNECT/CONNECT PROCEDURE (AUXILIARY BATTERY) .

Fig 11: Installing Left Outboard Cowl Vent Grille Trim Piece
Courtesy of GENERAL MOTORS CORP.