Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 152 (SUPPLEMENTAL INFLATABLE RESTRAINT SYSTEM)DISPOSAL PROCEDURESOFF-VEHICLE DEPLOYMENT
2004 Oldsmobile Bravada RWD
Off-Vehicle Deployment
2004 Oldsmobile Bravada RWDSECTION Off-Vehicle Deployment
WARNING: This page is about a different car, the 2002 Buick Park Avenue. However, it is still accessible from the selected car via links, so may be relevant.
- Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Turn ignition off and remove key. Put on safety glasses. Short 2 SIR Deployment Harness (J-38826) leads together by fully seating one banana plug into the other. Connect appropriate pigtail adapter included with deployment harness to SIR deployment harness. See Fig 1.
- Remove driver-side air bag module. See AIR BAG MODULES under REMOVAL & INSTALLATION. Remove horn lead, redundant steering wheel control leads, horn buttons and steering wheel control buttons from air bag module, if applicable.
- Clear space at least 6 feet (1.8 m) in diameter on shop floor or other surface (preferably paved surface outdoors) away from any loose or flammable objects. Place driver-side air bag module with vinyl trim cover facing up in center of cleared area. Extend SIR deployment harness and pigtail adapter to full length from air bag module. Place a 12-volt battery near shorted end of SIR deployment harness.
- Connect driver-side air bag module to SIR deployment harness using Pigtail Adapter (J-38826-50). Ensure area around air bag module is clear of people or loose objects. Verify that air bag module has trim cover facing up.
- Separate 2 banana plugs on SIR deployment harness. Connect SIR deployment harness wires to battery. Air bag module should deploy immediately. If air bag module does not deploy, go to step 8. Disconnect SIR deployment harness from battery. Short 2 SIR deployment harness leads together. DO NOT touch metal surfaces of air bag module for at least 10 minutes due to heat generated during deployment. Wear gloves and safety glasses when handling deployed air bag module. Wash hands with mild soap and water after handling air bag modules. Dispose of deployed air bag module as you would any other part. Inspect pigtail adapter and SIR deployment harness for damage after each use.
- Remove passenger-side air bag module. Mount passenger-side air bag module in Deployment Fixture (J39401-B). Repeat steps 2 through 5 for passenger-side air bag module, using Pigtail Adapter (J-38826-25).
- Remove appropriate side impact air bag module from vehicle. Mount side impact air bag module in Deployment Fixture (J39401-B). Repeat steps 2 through 5 for side impact air bag module, using Pigtail Adapter (J-38826-25).
- Ensure SIR deployment harness is disconnected from battery and that 2 banana plugs have been shorted together. Disconnect pigtail adapter from air bag module. Temporarily store air bag module with trim cover facing up. Contact manufacturer for additional instructions.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.