Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1454 (ENGINE CONTROLS (INTRODUCTION) -- 5.7L)COMPONENT LOCATORENGINE CONTROLS COMPONENT VIEWS
2004 Oldsmobile Bravada RWD
Engine Controls Component Views
2004 Oldsmobile Bravada RWDSECTION Engine Controls Component Views
WARNING: This page is about a different car, the 2004 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
| Callout | Component Name |
|---|---|
| 1 | Fuel Injector 6 |
| 2 | Fuel Injector 8 |
| 3 | Fuel Injector 3 |
| 4 | Fuel Injector 5 |
| 5 | Fuel Injector 7 |
| 6 | Ignition Coil/Module 7 |
| 7 | Ignition Coil/Module 5 |
| 8 | C109 |
| 9 | Ignition Coil/Module 3 |
| 10 | Ignition Coil/Module 1 |
| 11 | Engine Oil Temperature (EOT) Sensor |
| 12 | Engine Coolant Temperature (ECT) Sensor |
| 13 | Evaporative Emission (EVAP) Canister Purge Solenoid |
| 14 | Fuel Injector 1 |
| 15 | Throttle Actuator Control (TAC) Motor |
| 16 | Throttle Position (TP) Sensor |
| 17 | Fuel Injector 2 |
| 18 | Ignition Coil/Module 2 |
| 19 | Ignition Coil/Module 4 |
| 20 | Fuel Injector 4 |
| 21 | C110 |
| 22 | Ignition Coil/Module 6 |
| 23 | Ignition Coil/Module 8 |
| Callout | Component Name |
|---|---|
| 1 | Knock Sensor (KS) 1 |
| 2 | Knock Sensor (KS) 2 |
| Callout | Component Name |
|---|---|
| 1 | Generator |
| 2 | Mass Air Flow (MAF) Sensor |
| Callout | Component Name |
|---|---|
| 1 | A/C Refrigerant Pressure Sensor |
| 2 | Secondary Air Injection (AIR) Pump |
| 3 | SP100 |
| 4 | G102 |
| 5 | Headlamp Door Assembly-Right Connector |
| Callout | Component Name |
|---|---|
| 1 | Stop Lamp Switch C1 |
| 2 | Stop Lamp Switch C3 |
| 3 | C213 |
| 4 | Bose Signal Processor |
| 5 | Accelerator Pedal Position (APP) Sensor |
| 6 | Accelerator Pedal |
| 7 | Brake Pedal |
| 8 | Steering Wheel Position Sensor |
| 9 | Clutch Pedal |
| 10 | Clutch Pedal Start Switch |
| 11 | Clutch Pedal Position Switch |
| 12 | Stop Lamp Switch |
| 13 | Stop Lamp Switch Connector C2 |
| Callout | Component Name |
|---|---|
| 1 | Secondary Air Injection (AIR) Solenoid |
| 2 | Powertrain Control Module (PCM) |
| 3 | Throttle Actuator Control (TAC) Module |
| Callout | Component Name |
|---|---|
| 1 | Fuel Tank - Left |
| 2 | Fuel Pump and Sender Assembly |
| 3 | C402 |
| 4 | Fuel Tank Pressure (FTP) Sensor |
| 5 | Fuel Level Sensor - Right |
| 6 | Fuel Tank - Right |
| 7 | C414 |
| 8 | C412 |
| Callout | Component Name |
|---|---|
| 1 | Evaporative Emission (EVAP) Canister Vent Solenoid |
| Callout | Component Name |
|---|---|
| 1 | Battery |
| 2 | Battery Cables |
| 3 | G104 |
| 4 | Engine Coolant Reservoir |
| 5 | Fuse Block-Underhood |
| Callout | Component Name |
|---|---|
| 1 | Engine Oil Pressure (EOP) Sensor |
| 2 | Manifold Absolute Pressure (MAP) Sensor |
| 3 | Camshaft Position (CMP) Sensor |
| 4 | G107 |
| 5 | C112 |
| Callout | Component Name |
|---|---|
| 1 | Reverse Inhibit Solenoid |
| 2 | Skip Shift Solenoid |
| 3 | Vehicle Speed Sensor (VSS) |
| Callout | Component Name |
|---|---|
| 1 | Park/Neutral Position (PNP) Switch |
| Callout | Component Name |
|---|---|
| 1 | G105 |
| 2 | Engine Oil Temperature (EOT) Sensor |
| 3 | Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1 |
| Callout | Component Name |
|---|---|
| 1 | Crankshaft Position (CKP) Sensor |
| 2 | Heated Oxygen Sensor (HO2S) Bank 2 Sensor 1 |
| Callout | Component Name |
|---|---|
| 1 | Heated Oxygen Sensor (HO2S) Bank 1 Sensor 2 |
| 2 | Heated Oxygen Sensor (HO2S) Bank 2 Sensor 2 |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.