SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1411 (DOOR SYSTEM, MIRROR SYSTEM & WINDOW SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESPOWER WINDOWS INOPERATIVE - LOCKOUT FUNCTION
2004 Oldsmobile Bravada RWD

Power Windows Inoperative - Lockout Function

2004 Oldsmobile Bravada RWDSECTION Power Windows Inoperative - Lockout Function
WARNING: This page is about a different car, the 2002 Oldsmobile Bravada, 2002 GMC Envoy XL, 2002 GMC Envoy, and 2002 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
Power Windows Inoperative - Lockout Function

Step Action Yes No
Schematic Reference:  Power Window Schematics  
1 Did you perform the Door Systems Diagnostic System Check? Go to Step 2  Go to Diagnostic System Check - Door Systems 
2
  1. Disable the window lockout function.
  2. Operate the passenger power windows from the passenger door power window switches.
Do the passenger power windows operate normally?		 Go to Step 3  Go to Power Window Inoperative - Passenger Door (Front Door) Power Window Inoperative - Passenger Door (Rear Door(s)) 
3
  1. Enable the window lockout function.
  2. Operate the passenger power windows from the passenger door power window switches.
Do the passenger power windows operate up and down?		 Go to Step 4  Go to Testing for Intermittent Conditions and Poor Connections
4
  1. Install a scan tool.
  2. Monitor the window lockout data parameter in the driver door module input list.
  3. Place the window lockout switch in both the ON and OFF positions.
Does the window lockout data parameter change accordingly.		 Go to Step 5  Go to Step 10 
5 Does the window lockout function for the front passenger power window operate properly? Go to Step 6  Go to Step 9 
6
  1. Disable the window lockout function.
  2. Disconnect the appropriate rear window switch.
  3. Connect a test lamp to a good ground.
  4. Probe the rear window lockout signal circuit at the rear window switch harness connector.
Does the test lamp illuminate?		 Go to Step 7  Go to Step 11 
7 Test for a short to battery positive voltage on the rear window lockout signal circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 16  Go to Step 8 
8 Inspect for poor connections at the body control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 16  Go to Step 12 
9 Inspect for poor connections at the passenger door module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 16  Go to Step 13 
10 Inspect for poor connections at the driver door module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 16  Go to Step 14 
11 Inspect for poor connections at the rear power window switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 16  Go to Step 15 
12
IMPORTANT: Perform the set up procedure for the body control module. Refer to Body Control Module (BCM) Programming/RPO Configuration in Body Control System.
Replace the body control module. Refer to Body Control Module Replacement In Body Control System.		 Go to Step 16  -
13
IMPORTANT: Perform the set up procedure for the passenger door module. Refer to DCM Programming/RPO Configuration .
Replace the passenger door module. Refer to Switch Replacement - Door Lock and Side Window - Passenger .Did you complete the repair?		 Go to Step 16  -
14
IMPORTANT: Perform the set up procedure for the driver door module. Refer to DCM Programming/RPO Configuration .
Replace the driver door module. Refer to Switch Replacement - Door Lock and Side Window - Driver .Did you complete the repair?		 Go to Step 16  -
15 Replace the rear power window switch. Refer to Power Window Switch Replacement - Rear Door (Chevrolet) Power Window Switch Replacement - Rear Door (GMC/Oldsmobile) .
Did you complete the repair?		 Go to Step 16  -
16 Operate the system in order to verify the repair.
Did you correct the condition?		 System OK Go to Step 2 
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.