Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1227 (BUMPER SYSTEM)SPECIFICATIONS
2004 Oldsmobile Bravada RWD
Section 1227 (Bumper System): Specifications
2004 Oldsmobile Bravada RWDSECTION Specifications
WARNING: This page is about a different car, the 2003 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Antenna Ground Nut | 6 N.m | 53 lb in |
| Antenna Ground Stud | 5 N.m | 44 lb in |
| Air Deflector Bolts | 3 N.m | 27 lb in |
| Air Deflector Bolts | 7 N.m | 62 lb in |
| Backup Lamp/Rear Licese Bracket Screws | 1 N.m | 9 lb in |
| Brake Caliper Cooling Air Scoop Nuts | 3 N.m | 27 lb in |
| Brake Caliper Cooling Duct Bolt | 2 N.m | 18 lb in |
| Fascia Grille Screws | 2 N.m | 18 lb in |
| Fascia Lamp Deflector Bolts | 3 N.m | 27 lb in |
| Front Energy Absorber Bolts | 5 N.m | 44 lb in |
| Front Fascia Bracket Bolts | 7 N.m | 62 lb in |
| Front Fascia Lower Close Out Panel Bolts | 7 N.m | 62 lb in |
| Front Fascia Lower Flange to Radiator Support Screws | 8 N.m | 71 lb in |
| Front Fascia Retainer Bolts | 7 N.m | 62 lb in |
| Front Fascia to Fender Reinforcement Bolts | 5 N.m | 44 lb in |
| Front Fascia to Fender Reinforcement Stud Nut | 5 N.m | 44 lb in |
| Front Fascia to Skid Bar Bolt | 3 N.m | 27 lb in |
| Front Fascia Upper Flange Bolts | 5 N.m | 44 lb in |
| Front License Bracket Bolts | 1 N.m | 9 lb in |
| Front Wheelhouse to Fascia Bolts | 3 N.m | 27 lb in |
| License Bracket Screws | 2 N.m | 18 lb in |
| License Plate Opening to Absorber Screws | 1 N.m | 9 lb in |
| Outer Valance Bolts | 7 N.m | 62 lb in |
| Rear Energy Absorber Attaching Bolts | 5 N.m | 44 lb in |
| Rear Fascia Retainer Bracket Stud Nuts | 10 N.m | 89 lb in |
| Rear Fascia to Quarter Panel Reinforcement Screws | 5 N.m | 44 lb in |
| Rear Fascia to Rear Compartment Brace Bolts | 5 N.m | 44 lb in |
| Rear Fascia Upper Flange Screws | 2 N.m | 18 lb in |
| Rear License Plate Opening to Energy Absorber Screws | 1 N.m | 9 lb in |
| Reflector Nuts | 2 N.m | 18 lb in |
| Tail Lamp Screws | 2 N.m | 18 lb in |
| Valance Screws | 7 N.m | 62 lb in |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.