Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Fastener Tightening Specifications
2004 Oldsmobile Bravada RWDSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2004 Pontiac Aztek and 2004 Buick Rendezvous. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Accelerator Cable Bracket Retaining Bolts | 13 N.m | 115 lb in |
| Accelerator Cable Bracket Retaining Nut | 10 N.m | 89 lb in |
| Accelerator Pedal Retaining Bolt | 3 N.m | 27 lb in |
| Air Cleaner Duct Clamp | 2 N.m | 18 lb in |
| Air Cleaner Housing Bolt | 10 N.m | 89 lb in |
| AIR Crossover Pipe Bolt | 29 N.m | 80 lb in |
| AIR Shut-off Valve | 20 N.m | 15 lb ft |
| AIR Shut-off Valve Nut | 10 N.m | 89 lb in |
| AIR Shut-off Valve Pipe Adapter Bolt | 30 N.m | 22 lb ft |
| Camshaft Position (CMP) Sensor Retaining Bolt | 8 N.m | 71 lb in |
| Crankshaft Position 7X (CKP) Sensor Bolts | 11 N.m | 97 lb in |
| Crankshaft Position 24X (CKP) Sensor Bolts | 10 N.m | 89 lb in |
| Engine Coolant Temperature (ECT) Sensor | 20 N.m | 15 lb ft |
| EVAP Canister Bracket Retaining Nut | 10 N.m | 89 lb in |
| EVAP Canister Purge Valve Bracket | 10 N.m | 89 lb in |
| EVAP Canister Retaining Nut | 6 N.m | 53 lb in |
| Exhaust Gas Recirculation Pipe Bolt | 25 N.m | 18 lb ft |
| Exhaust Gas Recirculation Pipe Nut | 25 N.m | 18 lb ft |
| Exhaust Gas Recirculation Valve Attaching Bolts | 30 N.m | 22 lb ft |
| Fuel Filler Pipe Attaching Nut | 25 N.m | 18 lb ft |
| Fuel Filler Pipe Attaching Screw | 25 N.m | 18 lb ft |
| Fuel Filler Pipe Clamp | 2.5 N.m | 22 lb in |
| Fuel Filter Mounting Bracket Nut | 10 N.m | 89 lb in |
| Fuel Pressure Regulator Attaching Bolt | 8.5 N.m | 76 lb in |
| Fuel Pressure and Return Pipes | 17 N.m | 13 lb ft |
| Fuel Rail Attaching Nuts or Bolts | 10 N.m | 89 lb in |
| Fuel Tank Filler Pipe Hose Clamp | 2.5 N.m | 22 lb in |
| Fuel Tank Retaining Strap Bolts | 47 N.m | 35 lb ft |
| Heated Oxygen Sensors | 41 N.m | 30 lb ft |
| Idle Air Control Valve Attaching Screws | 3 N.m | 27 lb in |
| Ignition Coil to Ignition Control Module Screws | 4.5 N.m | 40 lb in |
| Ignition Control Module Bracket to Engine Studs and Nuts | 25 N.m | 18 lb ft |
| Knock Sensor | 19 N.m | 14 lb ft |
| Manifold Absolute Pressure (MAP) Sensor Retaining Bolt | 3 N.m | 27 lb in |
| Powertrain Control Module (PCM) Electrical Connector Screws | 8 N.m | 71 lb in |
| Secondary AIR Injection Check Valve Bracket Nut | 10 N.m | 89 lb in |
| Secondary AIR Injection Check Valve Mounting Bolt | 10 N.m | 89 lb in |
| Secondary AIR Injection Pipe Nut | 10 N.m | 89 lb in |
| Secondary AIR Injection Pump Bracket Bolt | 50 N.m | 37 lb ft |
| Secondary AIR Injection Vacuum Bleed Valve Bracket Nut | 10 N.m | 89 lb in |
| Throttle Body Retaining Nuts or Bolts | 28 N.m | 21 lb ft |
| Throttle Position Sensor Screws | 2 N.m | 18 lb in |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.