Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1022 (ENGINE COOLING SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2004 Oldsmobile Bravada RWD
Fastener Tightening Specifications
2004 Oldsmobile Bravada RWDSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Air Cleaner Outlet Duct Clamp (4.8L, 5.3L, and 6.0L) | 7 N.m | 62 lb in |
| Air Cleaner Outlet Duct Clamp (6.6L) | 6 N.m | 53 lb in |
| Air Conditioning (A/C) Compressor Bolt (6.6L) | 50 N.m | 37 lb ft |
| Air Inlet Tube Nut (6.6L) | 25 N.m | 18 lb ft |
| Auxiliary Water Pump Bracket Nut | 9 N.m | 80 lb in |
| Bypass Pipe to Water Pump Bolt (6.6L) | 21 N.m | 16 lb ft |
| Charged Air Cooler Duct Clamp (6.6L) | 6 N.m | 53 lb in |
| Coolant Air Bleed Pipe Cover Bolt (4.8L, 5.3L, and 6.0L) | 12 N.m | 106 lb in |
| Coolant Air Bleed Pipe Stud/Bolt (4.8L, 5.3L, and 6.0L) | 12 N.m | 106 lb in |
| Coolant Heater (4.8L, 5.3L, and 6.0L) | 50 N.m | 37 lb ft |
| Coolant Heater (8.1L) | 60 N.m | 47 lb ft |
| Coolant Heater Bolt (4.3L) | 2 N.m | 18 lb in |
| Coolant Heater Bolt (6.6L) | 2 N.m | 18 lb in |
| Coolant Heater Cord Bolt | 8 N.m | 71 lb in |
| Coolant Outlet Pipe Clip Bolt (6.6L) | 9 N.m | 80 lb in |
| Engine Block Coolant Drain Plug | 60 N.m | 44 lb ft |
| Engine Shield Bolt | 20 N.m | 15 lb ft |
| Exhaust Gas Recirculation (EGR) Coolant Pipe Bolt (6.6L) | 21 N.m | 16 lb ft |
| Exhaust Manifold Pipe Nut (4.8L, 5.3L, and 6.0L) | 50 N.m | 37 lb ft |
| Fan Clutch Bolt | 23 N.m | 17 lb ft |
| Fan Clutch Nut | 56 N.m | 41 lb ft |
| Fan Pulley Bolt/Nut (6.6L) | 46 N.m | 34 lb ft |
| Fan Shroud Bolt | 9 N.m | 80 lb in |
| Fuel Line Bracket Bolt (6.6L) | 21 N.m | 15 lb ft |
| Fuel Line to Fuel Injection Control Module Bolt (6.6L) | 35 N.m | 26 lb ft |
| Generator Bracket Bolt (6.6L and 8.1L) | 50 N.m | 37 lb ft |
| Generator Bracket Stud (8.1L) | 20 N.m | 15 lb ft |
| Generator Positive Cable Nut (6.6L) | 9 N.m | 80 lb in |
| Heater Inlet Pipe to Fuel Filter Bolt (6.6L) | 21 N.m | 16 lb ft |
| Heater Inlet Pipe to Thermostat Bolt (6.6L) | 21 N.m | 16 lb ft |
| Heater Outlet Hose Bracket Bolt (6.6L) | 21 N.m | 16 lb ft |
| Hood Hinge Bolts | 25 N.m | 18 lb ft |
| Idler Pulley Bolt (6.6L) | 43 N.m | 32 lb ft |
| Intake Manifold Cover Clamp (6.6L) | 6 N.m | 53 lb in |
| Junction Block Bracket Bolt (6.6L) | 9 N.m | 80 lb in |
| Main Electrical Harness Bracket Bolt (6.6L) | 21 N.m | 15 lb ft |
| Main Engine Electrical Harness Connector Bolt (6.6L) | 10 N.m | 89 lb in |
| Oil Cooler Hose Adapter Bolt (6.0L) | 12 N.m | 106 lb in |
| Oil Cooler Hose Bracket Bolt (6.0L) | 25 N.m | 18 lb ft |
| Oil Cooler Hose Bracket Bolt (8.1L) | 50 N.m | 37 lb ft |
| Positive Crankcase Ventilation (PCV) Oil Separator Bracket Nut (6.6L) | 21 N.m | 16 lb ft |
| Power Steering Pump Bracket Bolt (6.6L) | 46 N.m | 34 lb ft |
| Radiator Bolt | 25 N.m | 18 lb ft |
| Starter/Generator Control Module (SGCM) Brace Bolts | 25 N.m | 18 lb ft |
| Starter/Generator Control Module (SGCM) Coolant Pump Bolts | 9 N.m | 80 lb in |
| Starter/Generator Control Module (SGCM) Coolant Tank Bolts | 20 N.m | 15 lb ft |
| Starter/Generator Control Module (SGCM) Coolant Tank Nuts | 9 N.m | 80 lb in |
| Starter/Generator Control Module (SGCM) Cooling Fan Bolt | 9 N.m | 80 lb in |
| Starter/Generator Control Module (SGCM) Radiator Bolt | 9 N.m | 80 lb in |
| Starter/Generator Stator Coolant Inlet Pipe Bolt | 9 N.m | 80 lb in |
| Surge Tank Bolt/Nut | 9 N.m | 80 lb in |
| Thermal Bypass Fitting | 35 N.m | 26 lb ft |
| Thermal Bypass Hose Bolt | 10 N.m | 89 lb in |
| Thermostat Housing Bolt (4.8L, 5.3L, and 6.0L) | 15 N.m | 11 lb ft |
| Thermostat Housing Cover Bolt (6.6L) | 21 N.m | 16 lb ft |
| Thermostat Housing Crossover Bolt/Nut (6.6L) | 21 N.m | 16 lb ft |
| Transmission Control Module (TCM) Cover Bolt | 9 N.m | 80 lb in |
| Transmission Control Module (TCM) Electrical Connector Bolt | 8 N.m | 71 lb in |
| Turbocharger Coolant Bypass Valve (6.6L) | 60 N.m | 44 lb ft |
| Turbocharger Coolant Feed Pipe Bracket Bolt (6.6L) | 21 N.m | 16 lb ft |
| Turbocharger Coolant Feed Pipe Nut (6.6L) | 9 N.m | 80 lb in |
| Turbocharger Coolant Inlet Banjo Bolt (6.6L) | 25 N.m | 18 lb ft |
| Turbocharger Coolant Outlet Pipe Bolt/Nut (6.6L) | 9 N.m | 80 lb in |
| Water Crossover Bolt (8.1L) | 50 N.m | 37 lb ft |
| Water Outlet Bolt (8.1L) | 30 N.m | 22 lb ft |
| Water Outlet Stud (4.3L) | 25 N.m | 18 lb ft |
| Water Outlet Tube Bolt (6.6L) | 21 N.m | 16 lb ft |
| Water Pump Bolt (4.3L) | 45 N.m | 33 lb ft |
| Water Pump Bolt (4.8L, 5.3L, and 6.0L) | ||
|
15 N.m | 11 lb ft |
|
30 N.m | 22 lb ft |
| Water Pump Bolt (6.6L) | 21 N.m | 16 lb ft |
| Water Pump Bolt (8.1L) | 50 N.m | 37 lb ft |
| Water Pump Inlet Pipe Bolt (6.6L) | 21 N.m | 16 lb ft |
| Water Pump Pulley Bolt (4.3L) | 25 N.m | 18 lb ft |
| Water Pump to Oil Cooler Inlet Pipe Nut (6.6L) | 21 N.m | 16 lb ft |
| Wiring Harness Bracket to Thermostat Housing Bolt (6.6L) | 8 N.m | 71 lb in |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.