Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Engine Controls Component Views
2004 Oldsmobile Bravada AWDSECTION Engine Controls Component Views
WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
| Callout | Component Name |
|---|---|
| 1 | Ignition Coil 1 |
| 2 | Fuel Injector 1 |
| 3 | Fuel Injector 3 |
| 4 | Fuel Injector 5 |
| 5 | Fuel Injector 7 |
| 6 | Ignition Coil 7 |
| 7 | Ignition Coil 5 |
| 8 | Ignition Coil 3 |
| 9 | Engine Coolant Temperature (ECT) Sensor |
| Callout | Component Name |
|---|---|
| 1 | Ignition Coil 8 |
| 2 | Fuel Injector 2 Connector |
| 3 | Fuel Injector 4 |
| 4 | Ignition Coil 2 |
| 5 | Ignition Coil 4 |
| 6 | Fuel Injector 6 |
| 7 | Ignition Coil 6 |
| 8 | Fuel Injector 8 |
| Callout | Component Name |
|---|---|
| 1 | Manifold Absolute Pressure (MAP) Sensor |
| 2 | Throttle Body |
| 3 | Evaporative Emission (EVAP) Canister Purge Solenoid |
| Callout | Component Name |
|---|---|
| 1 | Knock Sensor (KS) 1 |
| 2 | Knock Sensor (KS) 2 |
| Callout | Component Name |
|---|---|
| 1 | Engine Oil Pressure (EOP) Sensor |
| 2 | Camshaft Position (CMP) Sensor |
| 3 | Camshaft Position (CMP) Sensor Connector |
| Callout | Component Name |
|---|---|
| 1 | CKP Mounting Bolt |
| 2 | CKP Mounting Location |
| 3 | Crankshaft Position (CKP) Sensor |
| Callout | Component Name |
|---|---|
| 1 | Bank 1 Sensor 2 HO2S |
| 2 | Bank 1 Sensor 1 HO2S |
| 3 | Bank 1 Sensor 1 HO2S Threaded Boss |
| 4 | Left Bank Catalytic Convertor |
| 5 | Bank 1 Sensor 2 HO2S Threaded Boss |
| 6 | Bank 2 Sensor 1 HO2S Threaded Boss |
| 7 | Right Side Frame Rail |
| 8 | Right Bank Catalytic Convertor |
| 9 | Bank 2 Sensor 2 HO2S Threaded Boss |
| 10 | Bank 2 Sensor 2 HO2S |
| 11 | Bank 2 Sensor 1 HO2S |
| Callout | Component Name |
|---|---|
| 1 | Bank 2 Sensor 1 HO2S |
| 2 | Bank 1 Sensor 2 HO2S Threaded Boss |
| 3 | Right Side Frame Rail |
| 4 | Right Bank Catalytic Convertor |
| 5 | Bank 2 Sensor 2 HO2S |
| 6 | Bank 2 Sensor 2 HO2S Threaded Boss |
| 7 | Left Bank Catalytic Convertor |
| 8 | Bank 1 Sensor 2 HO2S |
| 9 | Bank 1 Sensor 1 HO2S Threaded Boss |
| 10 | Bank 1 Sensor 1 HO2S |
| 11 | Bank 2 Sensor 1 HO2S Threaded Boss |
| Callout | Component Name |
|---|---|
| 1 | Fuel Pump and Sender Assembly Connector |
| 2 | Fuel Pump and Sender Assembly - Primary |
| Callout | Component Name |
|---|---|
| 1 | Fuel Pump and Sender Assembly - Secondary |
| 2 | Fuel Pump and Sender Assembly Connector |
| Callout | Component Name |
|---|---|
| 1 | Fuel Pump Relay - Secondary |
| Callout | Component Name |
|---|---|
| 1 | Fuel Pump and Sender Assembly |
| 2 | Fuel Tank Pressure (FTP) Sensor |
| 3 | Fuel Level Sensor |
| Callout | Component Name |
|---|---|
| 1 | Fuel Composition Sensor |
| Callout | Component Name |
|---|---|
| 1 | Left Frame Rail |
| 2 | Evaporative Emissions (EVAP) Canister Vent Solenoid |
| 3 | Fuel Tank |
| 4 | Evaporative Emissions (EVAP) Canister |
| Callout | Component Name |
|---|---|
| 1 | Clamp |
| 2 | Air Duct |
| 3 | Clamp |
| 4 | Intake Air Temperature (IAT)/Mass Air Flow (MAF) Sensor |
| 5 | Air Cleaner Assembly |
| 6 | Air Restriction Indicator |
| Callout | Component Name |
|---|---|
| 1 | Throttle Actuator Control (TAC) Module |
| 2 | Throttle Actuator Control (TAC) Connector |
| 3 | Fuse Block - Underhood |
| Callout | Component Name |
|---|---|
| 1 | Accelerator Pedal Position (APP) Sensor Connector |
| 2 | Accelerator Pedal Position (APP) Sensor |
| Callout | Component Name |
|---|---|
| 1 | Powertrain Control Module (PCM) |
| 2 | Radiator Support |
| 3 | Left Frame Rail |
| 4 | PCM Wire Harness Connectors |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.