Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 927 (BATTERY, CHARGING SYSTEM & STARTING SYSTEM)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2004 Oldsmobile Bravada AWD
Fastener Tightening Specifications
2004 Oldsmobile Bravada AWDSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2003 GMC Sonoma, 2003 GMC Jimmy, 2003 Chevrolet S10 Pickup, and 2003 Chevrolet Blazer. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Battery Hold Down Retainer Nut | 17 N.m | 13 lb ft |
| Battery Negative Cable to Engine (2.2L) | 12 N.m | 106 lb in |
| Battery Negative Cable to Engine Block Bolt (4.3L) | 17 N.m | 13 lb ft |
| Battery Negative Cable to Engine Block Bolt (2.2L) | 17 N.m | 13 lb ft |
| Battery Negative Cable to Frame (2.2L) | 6 N.m | 53 lb in |
| Battery Negative Cable to Frame (4.3L) | 9 N.m | 80 lb in |
| Battery Negative Cable to Radiator Support (2.2L) | 6 N.m | 53 lb in |
| Battery Negative Cable to Radiator Support (4.3L) | 9 N.m | 80 lb in |
| Battery Positive Cable Harness to Engine (4.3L) | 9 N.m | 80 lb in |
| Battery Positive Cable Nut | 6 N.m | 80 lb in |
| Battery Positive Cable to Generator Nut | 17 N.m | 13 lb ft |
| Battery Positive Cable to Starter Nut | 9 N.m | 80 lb in |
| Battery Positive Cable to Underhood Fuse Block Bolt | 10 N.m | 89 lb in |
| Battery Terminal Bolt | 15 N.m | 11 lb ft |
| Battery Tray Bolt | 25 N.m | 18 lb ft |
| Differential Carrier Shield Bolt | 25 N.m | 18 lb ft |
| Engine to Transmission Brace Bolt and Nut | 50 N.m | 37 lb ft |
| Engine Wiring Harness to Starter | 1.9 N.m | 17 lb in |
| Engine Wiring Harness Bracket to Generator Mounting Bracket Bolt | 25 N.m | 18 lb ft |
| Fan Pulley Bolt (2.2L) | 30 N.m | 22 lb ft |
| Generator Mounting Bolt (4.3L) | 50 N.m | 37 lb ft |
| Generator Mounting Bolt - Front (2.2L) | 25 N.m | 18 lb ft |
| Generator Mounting Bolt - Rear (2.2L) | 50 N.m | 37 lb ft |
| Generator Mounting Brace to Air Intake Plenum Stud Nut (2.2L) | 25 N.m | 18 lb ft |
| Generator Mounting Brace to Engine Stud Nut (2.2L) | 50 N.m | 37 lb ft |
| Generator Mounting Brace to Generator Bolt (2.2L) | 25 N.m | 18 lb ft |
| Generator Mounting Bracket Bolt (2.2L) | 50 N.m | 37 lb ft |
| Generator Mounting Bracket Bolt and Nut (4.3L) | 41 N.m | 30 lb ft |
| Generator Output (Bat) Terminal Nut | 17 N.m | 12 lb ft |
| Ground Strap to Cowl Bolt | 17 N.m | 12 lb ft |
| Ground Strap to Cowl Bolt/Nut | 50 N.m | 37 lb ft |
| Heater Hose Bracket to Generator Bolt (4.3L) | 25 N.m | 18 lb ft |
| Starter Motor Mounting Bolt (2.2L) | 43 N.m | 32 lb ft |
| Starter Motor Mounting Bolt (4.3L) | 50 N.m | 37 lb ft |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.