Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 910 (TRANSFER CASE - STEYR (UNIT REPAIR))SPECIFICATIONS
2004 Oldsmobile Bravada AWD
Section 910 (Transfer Case - STEYR (Unit Repair)): Specifications
2004 Oldsmobile Bravada AWDSECTION Specifications
WARNING: This page is about a different car, the 2003 Pontiac Montana, 2003 Pontiac Aztek, 2003 Oldsmobile Silhouette, 2003 Chevrolet Venture, and 2003 Buick Rendezvous. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Case-Le ft Drain Plug | 32 N.m | 24 lb ft |
| Case M10 Bolts | 60 N.m | 44 lb ft |
| Case M8 Bolts | 32 N.m | 23 lb ft |
| Differential Carrier Nut | 500 N.m | 369 lb ft |
| Extension Housing Bolts | 32 N.m | 23 lb ft |
| Extension Housing Drain Plug | 32 N.m | 23 lb ft |
| Extension Housing Fill Plug | 28 N.m | 21 lb ft |
| Flange Nut | 250 N.m | 185 lb ft |
| Holding Fixture J 44755 M10 Bolts | 50 N.m | 37 lb ft |
| Holding Fixture J 44755 M8 Bolts | 25 N.m | 18 lb ft |
| Output Driveshaft Housing M10 Bolts | 60 N.m | 44 lb ft |
| Output Driveshaft Housing M8 Bolts | 32 N.m | 23 lb ft |
| Output Driveshaft Nut | 505 N.m | 372 lb ft |
| Speed Sensor Bolt | 30 N.m | 22 lb ft |
| Transfer Case-to-Transaxle Bolts - in sequence | 50 N.m | 37 lb ft |
| Transfer Case-to-Transaxle M10 Brace Bolts | 56 N.m | 41 lb ft |
| Transfer Case-to-Transaxle M8 Brace Bolts | 32 N.m | 23 lb ft |
General Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Differential Bearing Preload | 0.1-0.15 mm | 0.004-0.006 in |
| Differential Carrier Rotating Torque | 1.5 N.m | 13 lb in |
| Drive and Driven Shafts Gears Backlash | 0.2-0.3 mm | 0.0078-0.0118 in |
| Drivenshaft Rotating Torque | 1.5 N.m | 13 lb in |
| Driveshaft Bearing Preload | 0.15 mm | 0.006 in |
| Driveshaft Rotating Torque | 1.5 N.m | 13 lb in |
| Extension Housing Gear Oil Fill Quantity | 290 ml | 9.80 oz |
| Gear Ratio Front-to-Rear | 1.013:1 | |
| Idler Gear Bearing Preload | 1.02-1.78 mm | 0.004-0.007 in |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.