Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 487 (COMMON SPECS & PROCEDURES)AIR CONDITIONINGAUTOMATIC & MANUAL SYSTEMA/C TORQUE SPECIFICATIONS
2004 Oldsmobile Bravada AWD
A/C Torque Specifications
2004 Oldsmobile Bravada AWDSECTION A/C Torque Specifications
WARNING: This page is about a different car, the 2003 Oldsmobile Bravada, 2003 GMC Envoy XL, 2003 GMC Envoy, and 2003 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
A/C TORQUE SPECIFICATIONS
| Application | Ft. Lbs. |
|---|---|
| A/C Compressor Mounting Bolt | 37 (50) |
| A/C Compressor Rear Bracket Bolt | 18 (25) |
| Accumulator-To-Evaporator Fitting | 21 (28) |
| Compressor Discharge Hose-To-Condenser Fitting | 21 (28) |
| Compressor Suction/Discharge Hose-To-Compressor Bolt | 24 (33) |
| Compressor Suction Hose-To-Accumulator Fitting | 35 (48) |
| Evaporator Tube-To-Condenser Fitting | 21 (28) |
| Heater Inlet & Outlet Hoses Bracket Bolt | 18 (25) |
| Heater Inlet Hose Fitting At Intake Manifold | 17 (24) |
| Heater Outlet Hose Bracket Bolt | 18 (25) |
| INCH Lbs. (N.m) | |
| A/C Compressor Cycling Switch | 44 (5) |
| A/C Evaporator & Blower Module Shield Screws | 19 (2.2) |
| A/C Refrigerant Pressure Sensor | 42 (4.8) |
| Accumulator Clamp Screw | 88 (10) |
| Actuator Retaining Screw | 17 (1.9) |
| Air Distributor Duct Mounting Screw | 17 (1.9) |
| Air Inlet Assembly Mounting Stud | 40 (4.5) |
| Air Outlet Assembly Retaining Screw | 22 (2.5) |
| Air Temperature Actuator Retaining Screw | 17 (1.9) |
| Blower Assembly Mounting Nut (RPO C42) | 40 (4.5) |
| Blower Assembly Mounting Screw (RPO C42) | 40 (4.5) |
| Blower Assembly Mounting Stud (RPO C42) | 40 (4.5) |
| Blower Motor Control Processor Mounting Screw | 17 (1.9) |
| Blower Motor Access Cover Screw (RPO C60 & C68) | 22 (2.5) |
| Blower Motor & Fan Assembly Mounting Screw | 17 (1.9) |
| Blower Motor Relay Bracket Mounting Screw | 17 (1.9) |
| Blower Motor Resistor Mounting Screw | 17 (1.9) |
| Body Harness Connector Support Bracket Mounting Nuts | 80 (9.0) |
| Compressor Pressure Relief Valve | 80 (9.0) |
| Condenser Insulator Retaining Screw | 17 (1.9) |
| Evaporator Case Section-To-Blower Case Section Retaining Screw | 17 (1.9) |
| Evaporator Tube Clip Screw | 17 (1.9) |
| Floor Air Outlet Mounting Screw | 17 (1.9) |
| Heater Core Access Cover Screw | 17 (1.9) |
| Heater/Vent Module Mounting Screw/Nut | 40 (4.5) |
| Heater/Vent Module Mounting Stud | 40 (4.5) |
| HVAC Control Module Retaining Screws | 17 (1.9) |
| HVAC Control Module Screw | 17 (1.9) |
| Intermediate Bracket Bolts | 88 (10) |
| Knee Bolster Bracket Nuts | 49 (5.5) |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.