Torque Specifications

2004 Oldsmobile Bravada AWDSECTION Torque Specifications
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2003 GMC Yukon XL, 2003 GMC Yukon, 2003 Chevrolet Tahoe, 2003 Chevrolet Suburban, and 2003 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Accelerator Pedal Position Sensor Retaining Bolts 15 (20)
Battery Cable-To-Battery Bolt 13 (17)
Engine Coolant Temperature Sensor 15 (20)
EVAP Canister Mounting Bolts 18 (25)
Fuel Composition Sensor Bracket-To-Frame Rail Mounting Nuts (5.3L Flex-Fuel) 13 (17)
Fuel Line Fittings 18 (25)
Fuel Tank Strap Retaining Bolts 30 (40)
Generator Mounting Bolts 37 (50)
Knock Sensors 15 (20)
Oxygen Sensors 31 (42)
Spare Tire Rear Crossmember Fasteners 37 (50)
Spark Plugs
4.8L, 5.3L & 6.0L (1)
8.1L (2)
Starter Mounting Bolts (4.8L, 5.3L & 6.0L) 37 (50)
INCH Lbs. (N.m) 
Camshaft Position Sensor Retaining Bolt/Screws
4.8L, 5.3L & 6.0L (3)
8.1L 106 (12.0)
Crankshaft Position Sensor Retaining Bolt
4.8L, 5.3L & 6.0L (4)
8.1L 106 (12.0)
EVAP Canister Purge Solenoid Retaining Bolts/Nuts 93 (10.5)
Fuel Composition Sensor-To-Mounting Bracket Bolts (5.3L Flex-Fuel) 89 (10.0)
Fuel Fill & Vent Pipe Hose Clamps 22 (2.5)
Fuel Filler Pipe Ground Strap Retaining Bolt (4.8L, 5.3L & 6.0L) 80 (9.0)
Fuel Filter Bracket Retaining Bolt 106 (12.0)
Fuel Rail Retaining Bolts
4.8L, 5.3L & 6.0L 89 (10.0)
8.1L 106 (12.0)
Generator Positive Post Cable Nut 80 (9.0)
Ignition Coil Retaining Bolts
4.8L, 5.3L & 6.0L 71 (8.0)
8.1L 106 (12.0)
Intake Manifold Sight Shield Bracket/Retainer Bolts/Nuts (4.8L, 5.3L, 6.0L & 8.1L) 44 (5.0)
Intake Manifold Sight Shield Fastener (4.8L, 5.3L, 6.0L & 8.1L) 89 (10.0)
MAF Sensor Hose Clamps 62 (7.0)
Manifold Absolute Pressure Sensor Retaining Bolt (8.1L) 106 (12.0)
PCM Harness Connector Fasteners 71 (8.0)
Positive Battery Cable-To-Solenoid Nut (4.8L, 5.3L & 6.0L) 80 (9.0)
Starter Solenoid Start Lead Terminal Nut (4.8L, 5.3L & 6.0L) 30 (3.4)
TAC Module Nuts 80 (9)
Throttle Body Mounting Nuts (4.8L, 5.3L, 6.0L & 8.1L) 89 (10.0)
Upper Engine Wiring Harness Retainer Nut (4.8L, 5.3L & 6.0L) 44 (5.0)
(1) If cylinder heads have not been replaced, tighten spark plugs to 11 ft. lbs. (15 N.m). With NEW aluminum cylinder heads, tighten spark plugs to 15 ft. lbs. (20 N.m). With NEW iron cylinder heads, tighten spark plugs to 22 ft. lbs. (30 N.m).
(2) If cylinder heads have not been replaced, tighten spark plugs to 15 ft. lbs. (20 N.m). With NEW iron cylinder heads, tighten spark plugs to 22 ft. lbs. (30 N.m).
(3) Tighten to 21 ft. lbs. (29 N.m).
(4) Tighten to 18 ft. lbs. (25 N.m).
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.