Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 33 (HVAC SYSTEMS - MANUAL)TORQUE SPECIFICATIONS
2004 Oldsmobile Bravada AWD
Torque Specifications
2004 Oldsmobile Bravada AWDSECTION Torque Specifications
WARNING: This page is about a different car, the 2002 Pontiac Grand Prix. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | ||
|---|---|---|---|
| A/C Compressor Mounting Bolt (3.1L) | 37 (50) | ||
| A/C Compressor Mounting Bolt (3.8L) | |||
| Bracket-To-Engine (Lower) | 59 (80) | ||
| Bracket-To-Engine (Upper) | 37 (50) | ||
| Bracket-To-Compressor (Nut) | 74 (100) | ||
| Evaporator Core Block Fitting Bolt | 12 (16) | ||
| Liquid Line At Block Fitting | 12 (16) | ||
| Liquid Line Nut At Condenser | 20 (27) | ||
| Liquid Line Nut At Orifice | 20 (27) | ||
| Refrigerant Line Fitting | |||
| At Accumulator | 12 (16) | ||
| At Compressor (Nut) | 24 (33) | ||
| At Condenser | 12 (16) | ||
| INCH Lbs. (N.m) | |||
| Accumulator Strap Bolt | 36 (4.1) | ||
| Actuator Mounting Bolt | 13 (1.5) | ||
| Air Distributor Case Screw | 13 (1.5) | ||
| A/C Compressor Pressure Relief Valve | 80 (9.0) | ||
| A/C Pressure Sensor | 41 (4.6) | ||
| Blower Motor Screw | 12 (1.3) | ||
| Blower Motor Resistor Screw | 13 (1.5) | ||
| Heater Core Cover Screw | 13 (1.5) | ||
| Heater Core Line Clamp Screw | 13 (1.5) | ||
| Heater Core Mounting Clip Screw | 13 (1.5) | ||
| HVAC Module Screw | 18 (2.0) | ||
| HVAC Module-To-Dash Bolt/Nut | 89 (10) | ||
| HVAC Module Upper Case Screw | 13 (1.5) | ||
| Instrument Panel Compartment Screw | 18 (2.0) | ||
| Recirculation Housing Screws | 13 (1.5) | ||
| Temperature Actuator Screw | 13 (1.5) | ||
| Vacuum Tank Screw | 13 (1.5) | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.