Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 31 (HVAC SYSTEMS - MANUAL)TORQUE SPECIFICATIONS
2004 Oldsmobile Bravada AWD
Torque Specifications
2004 Oldsmobile Bravada AWDSECTION Torque Specifications
WARNING: This page is about a different car, the 2002 Buick Regal and 2002 Buick Century. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | |
|---|---|---|
| Compressor Mounting Bolts | ||
| Front Bolt | 37 (50) | |
| Lower Bolt | 22 (30) | |
| Rear Bolt | 37 (50) | |
| Rear Bracket | 23 (31) | |
| Condenser Block Fitting Nut | 20 (27) | |
| Evaporator Block Fitting Nut | 12 (16) | |
| Evaporator Inlet Tube Nut | 20 (27) | |
| Refrigerant Line Fittings | ||
| At Accumulator | 12 (16) | |
| At Compressor (Nut) | 24 (33) | |
| At Condenser | 12 (16) | |
| At Evaporator (Bolt) | 12 (16) | |
| At Orifice Tube | 20 (27) | |
| INCH Lbs. (N.m) | ||
| A/C Compressor Pressure Relief Valve | 80 (9.0) | |
| A/C Refrigerant Filter Nut | 133 (15) | |
| A/C Pressure Sensor | 41 (4.6) | |
| Accumulator Strap Bolt | 36 (4.1) | |
| Air Inlet Housing Retaining Screw | 14 ()1.6 | |
| Blower Motor Screw | 12 (1.3) | |
| Blower Motor Resistor Screw | 13 (1.5) | |
| Heater Core Cover Screw | 13 (1.5) | |
| Heater Core Support Bracket Nut | 40 (4.5) | |
| HVAC Control Module Screws | 18 (2) | |
| HVAC Module Assembly Screws | 13 (1.5) | |
| HVAC Module Assembly Nut | 89 (10) | |
| HVAC Module Assembly Upper Mounting Screw | 14 (1.6) | |
| Recirculation Housing Screw | 13 (1.5) | |
| Temperature Actuator Screw | 13 (1.5) | |
| Vacuum Tank Screw | 13 (1.5) | |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.