SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2050 (COMPONENT CONNECTOR END VIEWS & INDEX - (1 OF 5))COMPONENT CONNECTOR END VIEWSBODY CONTROL MODULE (BCM) X5
2004 Oldsmobile Bravada AWD

Body Control Module (BCM) X5

2004 Oldsmobile Bravada AWDSECTION Body Control Module (BCM) X5
WARNING: This page is about a different car, the 2009 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Body Control Module (BCM) X5 Connector End View
GM1664500Courtesy of GENERAL MOTORS CORP.
Body Control Module (BCM) X5

Pin Wire Circuit Function
1 0.8 YE 18 Left Rear Stop/Turn Lamp Supply Voltage
2 0.8 D-GN 19 Right Rear Stop/Turn Lamp Supply Voltage
3 - - Not Used
4 0.8 L-BU/WH 1314 Left Front Turn Signal Lamp Supply Voltage
5 0.8 WH 5065 Stop Lamp Relay Coil Supply Voltage
6 0.5 WH 17 Stop Lamp Supply Voltage
7 - - Not Used
8 0.35 PK 5076 5-Volt Reference
9 0.35 WH 5075 Current Sensor Signal
10 0.35 BN 5077 Low Reference
11 0.35 TN 755 RAP Relay Coil Control
12 - - Not Used
13 0.35 L-GN 5486 Run Relay Coil Control
14 0.35 BN 4 Accessory Voltage
15 0.35 PU 5531 Hood Closed Switch Signal (AP3)
16 0.35 L-BU 1134 Park Brake Switch Signal
17 - - Not Used
18 0.35 TN 28 Horn Relay Control
19 - - Not Used
20 0.35 GY 91 Windshield Wiper Switch Signal 2
21 0.35 TN 860 Front Windshield Wiper Switch High Signal
22 - - Not Used
23 0.35 PK/WH 1970 Headlamp Low Beam Relay Control
24 0.35 D-BU 45 Park Lamp Supply Voltage
25 - - Not Used
Connector Part Information 
  • OEM: 15480179
  • Service: 88988837
  • Description: 25-Way F HIT Series (BN)
Terminal Part Information 
  • Pins: 1-2, 4-5
  • Terminal/Tray: SNAC-A061T-M2.8/20
  • Core/Insulation Crimp: E/A
  • Release Tool/Test Probe: 15315247/J-35616-4A (PU)
  • Pins: 6, 8-11, 13-16, 18, 20-21, 23-24
  • Terminal/Tray: SNAC3-A021T-M0.64/20
  • Core/Insulation Crimp: J/J
  • Release Tool/Test Probe: 15315247/J-35616-64B (L-BU)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.