Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Fastener Tightening Specifications
2004 Oldsmobile Bravada AWDSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2009 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Accelerator Pedal Bolt | 10 N.m | 89 lb in |
| Air Cleaner Assembly Bolt | 6 N.m | 53 lb in |
| Air Cleaner Inlet Duct Bolt | 6 N.m | 53 lb in |
| Air Cleaner Outlet Duct Clamp | 3 N.m | 27 lb in |
| Air Cleaner Upper Housing Screw | 3 N.m | 27 lb in |
| Camshaft Position (CMP) Sensor Bolt | 10 N.m | 89 lb in |
| Crankshaft Position (CKP) Sensor Stud | 10 N.m | 89 lb in |
| Engine Coolant Temperature (ECT) Sensor | 20 N.m | 15 lb ft |
| Engine Wiring Harness Heat Shield Bolt/Nut | 10 N.m | 89 lb in |
| Evaporative Emission (EVAP) Canister Nut | 8 N.m | 71 lb in |
| Evaporative Emission (EVAP) Canister Purge Solenoid Bolt | 16 N.m | 12 lb ft |
| Fuel Fill Pipe Hose Clamp | 5 N.m | 44 lb in |
| Fuel Injector Wiring Harness Electrical Connector Bracket Bolt | 14 N.m | 10 lb ft |
| Fuel Pressure Sensor | 15 N.m | 11 lb ft |
| Fuel Pump Flow Control Module Bolt | 10 N.m | 89 lb in |
| Fuel Rail Bolt | 10 N.m | 89 lb in |
| Fuel Tank Fill Pipe Bracket Bolt | 4 N.m | 35 lb in |
| Fuel Tank Fill Pipe Housing to Fuel Tank Fill Pipe Screw | 10 N.m | 89 lb in |
| Fuel Tank Strap Bolt | 20 N.m | 15 lb ft |
| Heated Oxygen Sensor (HO2S) | 42 N.m | 31 lb ft |
| Ignition Coil Bolt/Nut | 25 N.m | 18 lb ft |
| Ignition Coil Bracket Stud | 25 N.m | 18 lb ft |
| Intake Manifold Upper Bolt | 25 N.m | 18 lb ft |
| Knock Sensor Bolt | 25 N.m | 18 lb ft |
| Mass Airflow (MAF)/Intake Air Temperature (IAT) Sensor Bolt | 4 N.m | 34 lb in |
| Rear Brake Pipe Fitting to Brake Pressure Modulator Valve (BPMV) | 21 N.m | 16 lb ft |
| Rear Brake Pipe Fitting to Rear Brake Crossover Pipe Fitting | 18 N.m | 13 lb ft |
| Rear Brake Pipe Fitting to Rear Brake Hose Fitting | 18 N.m | 13 lb ft |
| Spark Plug | 15 N.m | 11 lb ft |
| Throttle Body Bolt/Nut | 10 N.m | 89 lb in |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.