SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1955 (ENGINE MECHANICAL - 3.5L)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2004 Oldsmobile Bravada AWD

Fastener Tightening Specifications

2004 Oldsmobile Bravada AWDSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2009 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
Application Specification
Metric English
A/C Compressor Bracket Bolt 50 N.m 37 lb ft
Camshaft Position Actuator Assembly Bolt 16 N.m 12 lb ft
Camshaft Position Actuator Magnet Bolt 10 N.m 89 lb in
Camshaft Position Sensor Bolt 10 N.m 89 lb in
Camshaft Thrust Plate Screw 10 N.m 89 lb in
Clutch Pressure Plate Bolt 25 N.m 18 lb ft
Connecting Rod Bearing Cap Bolt
  • First Pass
 25 N.m 18 lb ft
  • Final Pass
 110 degrees
Coolant Crossover Pipe Bolt - Front 50 N.m 37 lb ft
Coolant Crossover Pipe Bolt - Side 10 N.m 89 lb in
Coolant Drain Plug 19 N.m 14 lb ft
Coolant Temperature Sensor 23 N.m 17 lb ft
Crankshaft Balancer Bolt
  • Installation Pass Using the Old Bolt to Ensure the Balancer is Completely Installed
 125 N.m 92 lb ft
  • First Pass - Install a NEW Bolt After the Installation Pass and Tighten as Described in the First and Final Passes
 125 N.m 92 lb ft
  • Final Pass
 130 degrees
Crankshaft Main Bearing Cap Bolt/Stud
  • First Pass
 50 N.m 37 lb ft
  • Final Pass
 77 degrees
Crankshaft Oil Deflector Nut 25 N.m 18 lb ft
Crankshaft Position Sensor Shield Nut 11 N.m 98 lb in
Crankshaft Position Sensor Stud 11 N.m 98 lb in
Cylinder Head Bolt
  • First Pass
 60 N.m 44 lb ft
  • Final Pass
 95 degrees
Drive Belt Idler Pulley Bolt - 13 mm 30 N.m 22 lb ft
Drive Belt Idler Pulley Bolt - 15 mm 50 N.m 37 lb ft
Drive Belt Tensioner Bolt 50 N.m 37 lb ft
Engine Block Heater 50 N.m 37 lb ft
Engine Block Plug 60 N.m 44 lb ft
Engine Front Cover Bolt 25 N.m 18 lb ft
Engine Lift Bracket Bolt 70 N.m 52 lb ft
Engine Mount Bolts 110 N.m 81 lb ft
Engine Mount Bracket Bolts
  • M10
 50 N.m 37 lb ft
  • M12
 110 N.m 81 lb ft
Engine Mount Nuts 85 N.m 63 lb ft
Engine Oil Pressure Switch 16 N.m 12 lb ft
Engine Wiring Harness Bracket Bolt 13 N.m 115 lb in
EVAP Canister Purge Solenoid Valve Bolts 16 N.m 12 lb ft
EVAP Purge Valve Bolt 12 N.m 106 lb in
Exhaust Crossover Heat Shield Bolts 10 N.m 89 lb in
Exhaust Crossover Pipe Nuts 25 N.m 18 lb ft
Exhaust Crossover Pipe Studs 25 N.m 18 lb ft
Exhaust Manifold Bolt 20 N.m 15 lb ft
Exhaust Manifold Heat Shield Bolt 10 N.m 89 lb in
Exhaust Manifold Lower Heat Shield Bolt 10 N.m 89 lb in
Flywheel Bolt
  • Automatic Transmission
 70 N.m 52 lb ft
  • Manual Transmission - First Pass
 50 N.m 37 lb ft
  • Manual Transmission - Final Pass
 70 degrees
Front Oil Gallery Plug 33 N.m 24 lb ft
Fuel Injector Rail Bolt 10 N.m 89 lb in
Heated Oxygen Sensor 42 N.m 31 lb ft
Heater Inlet and Outlet Pipe Bolt - 10 mm 10 N.m 89 lb in
Heater Inlet and Outlet Pipe Bolt/Nut - 13 mm 25 N.m 18 lb ft
Heater Inlet Pipe Stud 35 N.m 26 lb ft
Ignition Coil Bracket Bolt/Nut/Stud 25 N.m 18 lb ft
Knock Sensor 25 N.m 18 lb ft
Lower Intake Manifold Bolt - Center
  • First Pass
 7 N.m 62 lb in
  • Final Pass
 13 N.m 115 lb in
Lower Intake Manifold Bolt - Corner
  • First Pass
 7 N.m 62 lb in
  • Final Pass
 25 N.m 18 lb ft
MAP Sensor Bracket Bolts 25 N.m 18 lb ft
Oil Filter 30 N.m 22 lb ft
Oil Filter Adapter Bolt 25 N.m 18 lb ft
Oil Filter Adapter Heat Shield Nuts 25 N.m 18 lb ft
Oil Filter Fitting 39 N.m 29 lb ft
Oil Level Indicator Tube Bolt 25 N.m 18 lb ft
Oil Pan Bolt 25 N.m 18 lb ft
Oil Pan Drain Plug 25 N.m 18 lb ft
Oil Pan Side Bolt
  • First Pass
 50 N.m 37 lb ft
  • Final Pass
 50 degrees
Oil Pan Support Bracket Bolt 50 N.m 37 lb ft
Oil Pump Cover Bolt 10 N.m 89 lb in
Oil Pump Drive Gear Clamp Bolt 36 N.m 27 lb ft
Oil Pump Mounting Bolt 41 N.m 30 lb ft
Piston Oil Nozzle Bolt 10 N.m 89 lb in
Rear Oil Gallery Plug - 3/8 inch 33 N.m 24 lb ft
Spark Plug 15 N.m 11 lb ft
Throttle Body Bolt/Nut 10 N.m 89 lb in
Throttle Body Heater Coolant Inlet and Outlet Hose Pipe Nuts 10 N.m 89 lb in
Throttle Body Stud 6 N.m 53 lb in
Timing Chain Tensioner Bolt 21 N.m 15 lb ft
Torque Converter Cover Bolts 12 N.m 106 lb in
Torque Converter to Flexplate Bolts 62 N.m 46 lb ft
Transaxle to Engine Bolts 75 N.m 55 lb ft
Upper Intake Manifold Bolt/Stud 25 N.m 18 lb ft
Valve Lifter Guide Bolt 10 N.m 89 lb in
Valve Lifter Oil Manifold Cover Plate Bolt 25 N.m 18 lb ft
Valve Rocker Arm Bolt 34 N.m 25 lb ft
Valve Rocker Arm Cover Bolt 10 N.m 89 lb in
Water Inlet Bolt/Stud 10 N.m 89 lb in
Water Pump Bolt 25 N.m 18 lb ft
Water Pump Pulley Bolt 25 N.m 18 lb ft
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.