SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1950 (ENGINE MECHANICAL - 2.4L)SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2004 Oldsmobile Bravada AWD

Fastener Tightening Specifications

2004 Oldsmobile Bravada AWDSECTION Fastener Tightening Specifications
WARNING: This page is about a different car, the 2009 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.
Application Specification
Metric English
3-Phase Cable Bracket to Tie Bar Bolt 10 N.m 89 lb in
Auxiliary Heater Water Pump Bolt 9 N.m 80 lb in
A/C Compressor to Block Bolts 22 N.m 16 lb ft
Balance Shaft Adjustable Chain Guide Bolt 15 N.m 11 lb ft
Balance Shaft Bearing Carrier to Block Bolt 10 N.m 89 lb in
Balance Shaft Fixed Chain Guide Bolt 15 N.m 11 lb ft
Balance Shaft Sprocket Bolt 50 N.m 37 lb ft
Battery Positive Cable to Starter Motor Nut 9 N.m 80 lb in
Block Core Plug 40 N.m 30 lb ft
Block Heater Bolt 10 N.m 89 lb in
Cam Cover to Cylinder Head Bolt 10 N.m 89 lb in
Cam Cover to Ground Cable Bolt 10 N.m 89 lb in
Cam Cover to Ground Cable Stud 10 N.m 89 lb in
Camshaft
  • Camshaft Cap Bolt
 10 N.m 89 lb in
  • Camshaft Position Actuator Solenoid Valve Bolt
 10 N.m 89 lb in
  • Camshaft Position Sensor Bolt
 10 N.m 89 lb in
  • Camshaft Timing Chain Tensioner
 75 N.m 55 lb ft
  • Exhaust Camshaft Position Actuator - First Pass
 30 N.m 22 lb ft
  • Exhaust Camshaft Position Actuator - Final Pass
 100 degrees
  • Intake Camshaft Position Actuator - First Pass
 30 N.m 22 lb ft
  • Intake Camshaft Position Actuator - Final Pass
 100 degrees
  • Intake Camshaft Rear Cap Bolt
 25 N.m 18 lb ft
Chain Guide Plug 90 N.m 59 lb ft
Connecting Rod Bolt
  • First Pass
 25 N.m 18 lb ft
  • Final Pass
 100 degrees
Crankshaft Balancer Bolt
  • First Pass
 100 N.m 74 lb ft
  • Final Pass
 125 degrees
Crankshaft Bearings - Lower Crankcase to Block - Bedplate
  • First Pass
 20 N.m 15 lb ft
  • Final Pass
 70 degrees
Crankshaft Position Reluctor Ring 15 N.m 11 lb ft
Crankshaft Position Sensor Bolt 10 N.m 89 lb in
Cylinder Head Bolt
  • First Pass
 30 N.m 22 lb ft
  • Final Pass
 155 degrees
Cylinder Head Front Chaincase Bolt 35 N.m 26 lb ft
Cylinder Head Oil Gallery Plug 35 N.m 26 lb ft
Drive Belt Spring Tensioner Bolts 22 N.m 16 lb ft
Drive Belt Tensioner Bracket Bolt 58 N.m 43 lb ft
EGR Cover Bolt 25 N.m 18 lb ft
Engine Coolant Temperature Sensor 20 N.m 15 lb ft
Engine Lift Bracket Front Bolt 25 N.m 18 lb ft
Engine Lift Bracket Rear Bolt 25 N.m 18 lb ft
Engine Mount Bolts 50 N.m 37 lb ft
Engine Mount Bracket Bolts 100 N.m 74 lb ft
Engine Wiring Harness Ground Terminal Bolt 20 N.m 15 lb ft
EVAP Canister Valve Bolt 22 N.m 16 lb ft
Exhaust Manifold Pipe Flange Stud 16 N.m 12 lb ft
Exhaust Manifold to Cylinder Head Nut - 2 passes 14 N.m 124 lb in
Exhaust Manifold to Cylinder Head Stud 10 N.m 89 lb in
Flywheel Bolt - Automatic Transmission
  • First Pass
 53 N.m 39 lb ft
  • Final Pass
 25 degrees
Flywheel Bolt - Manual Transmission
  • First Pass
 53 N.m 39 lb ft
  • Final Pass
 25 degrees
Frame to Body Bolts - Use new bolts 155 N.m 114 lb ft
Front Cover to Block Bolt 25 N.m 18 lb ft
Front Lift Bracket Bolt 25 N.m 18 lb ft
Fuel Pipe Bracket Bolt 10 N.m 89 lb in
Fuel Rail Bracket Stud 10 N.m 89 lb in
Generator Control Module Coolant Pump to Block Bolts 25 N.m 18 lb ft
Generator to Block Bolt 23 N.m 17 lb ft
Heat Shield to Exhaust Manifold Bolt 22 N.m 16 lb ft
Ignition Coil Bolt 10 N.m 89 lb in
Intake Manifold to Cylinder Head Bolt 10 N.m 89 lb in
Intake Manifold to Cylinder Head Nut 10 N.m 89 lb in
Intake Manifold to Cylinder Head Stud 6 N.m 53 lb in
Knock Sensor Bolt 25 N.m 18 lb ft
Lower Crankcase to Block Perimeter Bolt 25 N.m 18 lb ft
Oil Filter Housing Cover 22 N.m 16 lb ft
Oil Gallery Gerotor Cover - Rear Bolt 6 N.m 53 lb in
Oil Gallery Plug 35 N.m 26 lb ft
Oil Gallery Plug - Rear 60 N.m 44 lb ft
Oil Level Indicator Tube to Intake Manifold Bolt 10 N.m 89 lb in
Oil Pan Drain Plug 25 N.m 18 lb ft
Oil Pan to Block Bolts 25 N.m 18 lb ft
Oil Pan to Transaxle Bolts 75 N.m 55 lb ft
Oil Pressure Switch 22 N.m 16 lb ft
Oil Pump Cover Bolt 6 N.m 53 lb in
Oil Pump Pressure Relief Valve Plug 40 N.m 30 lb ft
Oxygen Sensor 42 N.m 31 lb ft
Piston Oil Squirter 15 N.m 11 lb ft
Spark Plug 20 N.m 15 lb ft
Starter Generator Bolts 58 N.m 43 lb ft
Starter Motor to Block Bolt 53 N.m 39 lb ft
Thermostat Housing to Block Bolts 10 N.m 89 lb in
Throttle Body Bolt 10 N.m 89 lb in
Throttle Body Nut 10 N.m 89 lb in
Throttle Body Stud 6 N.m 53 lb in
Timing Adjustable Chain Guide Bolt 10 N.m 89 lb in
Timing Chain Oil Nozzle Bolt 10 N.m 89 lb in
Timing Fixed Chain Guide Bolt 15 N.m 11 lb ft
Timing Upper Chain Guide Bolt 10 N.m 89 lb in
Torque Converter to Flexplate Bolts 60 N.m 44 lb ft
Vent Tube to Cylinder Head 15 N.m 11 lb ft
Water Jacket Drain Plug 20 N.m 15 lb ft
Water Pipe Support Bracket Bolt 10 N.m 89 lb in
Water Pump Access Cover Bolt 7 N.m 62 lb in
Water Pump/Balance Shaft Chain Tensioner Bolt 10 N.m 89 lb in
Water Pump Bolts 25 N.m 18 lb ft
Water Pump Sprocket Bolt 10 N.m 89 lb in
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.