SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1763 (ENGINE CONTROL SYSTEM - 4.2L - DTC P0507 TO P2401)DIAGNOSTIC INFORMATION & PROCEDURESDTC P060D: CONTROL MODULE ACCELERATOR PEDAL POSITION (APP) SYSTEM PERFORMANCETEST DESCRIPTION
2004 Oldsmobile Bravada AWD

Test Description

2004 Oldsmobile Bravada AWDSECTION Test Description
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2005 Isuzu Ascender, 2005 GMC Envoy XUV, 2005 GMC Envoy XL, 2005 GMC Envoy, and 2005 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  A DTC P0602 indicates that the PCM is not programmed.
  1. 5:  Resistance is measured at the pedal assembly because a pedal resistance that is lower than the specified value will set this DTC.
DTC P060D

Step Action Values Yes No
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2  Is DTC P0602 set? - Go to Step 3  Go to Step 5 
3 Program the powertrain control module (PCM). Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Does DTC P0602 reset?		 - Go to Step 4  Go to Step 8 
4
  1. Ensure that all tool connections are secure.
  2. Ensure that the programming equipment is operating correctly.
  3. Ensure that the correct software/calibration package is used.
  4. Attempt to program the PCM. Refer to Service Programming System (SPS) in Programming and Setup.
Does DTC P0602 reset?		 - Go to Step 7  Go to Step 8 
5 
  1. Turn OFF the ignition.
  2. Disconnect the accelerator pedal connector
  3. Ensure that the pedal is at the rest position.
  4. Measure the resistance from the 5-volt reference of the accelerator pedal assembly to the accelerator pedal position (APP) sensor 2 signal of the accelerator pedal assembly with a DMM. Refer to Circuit Testing in Wiring Systems.
Is the resistance less than the specified value?		 450 Ω Go to Step 6  Go to Step 7 
6 Replace the accelerator pedal assembly. Refer to Accelerator Pedal Position (APP) Sensor Replacement .
Did you complete the replacement?		 - Go to Step 8  -
7 Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 8  -
8
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 9 
9 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information System OK
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.