SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1754 (THEFT DETERRENT SYSTEM)REPAIR INSTRUCTIONSTHEFT DETERRENT INCLINATION SENSOR REPLACEMENTINSTALLATION PROCEDURE
2004 Oldsmobile Bravada AWD

Installation Procedure

2004 Oldsmobile Bravada AWDSECTION Installation Procedure
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2005 Isuzu Ascender, 2005 GMC Envoy XUV, 2005 GMC Envoy XL, 2005 GMC Envoy, and 2005 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
  1. Clean the floor panel to ensure the mounting location is free of dirt or debris.
    2. Fig 1: Positioning Theft Deterrent Inclination Sensor
    GM1198138Courtesy of GENERAL MOTORS CORP.
  2. Remove the protective backing to the adhesive strip on the bottom of the sensor (1).
  3. The mounting location for the sensor is on the floor panel, 55mm (2in) (A) forward of the electrical harness channel, 126mm (5in) (B) inboard from the electrical harness channel. Attach the sensor to the floor panel.
    4. Fig 2: Locating Theft Deterrent Inclination Sensor
    GM1198136Courtesy of GENERAL MOTORS CORP.
  4. Connect the sensor (1) electrical sensor.
  5. Position the carpet to the original location.
  6. Install the right child restraint tether anchors. Refer to Child Restraint Tether Anchor Replacement - Rear No. 1 (TrailBlazer, Envoy, Bravada) or Child Restraint Tether Anchor Replacement - Rear No. 1 (TrailBlazer EXT, Envoy XL) in Seat Belts.
  7. Install the right lower rear quarter trim panel. Refer to Trim Panel Replacement - Rear Quarter - Right (TrailBlazer EXT, Envoy XL) or Trim Panel Replacement - Rear Quarter - Right (Trailblazer, Envoy, Rainier) in Interior Trim.
  8. Install the right center pillar trim panel. Refer to Garnish Molding Replacement - Center Pillar in Interior Trim.
  9. Install the lift gate door sill plate. Refer to Door Sill Plate Replacement - Liftgate in Interior Trim.
  10. Install the right rear door sill plate. Refer to Door Sill Plate Replacement - Rear (TrailBlazer EXT, Envoy XL, Envoy XUV) or Door Sill Plate Replacement - Rear (Trailblazer, Envoy, Rainier) in Interior Trim.
  11. Install the right seat back. Refer to Seat Back Replacement - Rear No. 1 (TrailBlazer EXT, Envoy XL, Envoy XUV) or Seat Back Replacement - Rear No. 1 (TrailBlazer, Envoy, Rainier) in Seats.
  12. Install the navigation control processor bracket. Refer to Navigation Control Processor Bracket Replacement (TrailBlazer EXT, Envoy XL) or Navigation Control Processor Bracket Replacement (Trailblazer, Envoy, Rainier) in Cellular Communication.
  13. Install the communication interface module. Refer to Communication Interface Module Replacement (TrailBlazer EXT, Envoy XL) or Communication Interface Module Replacement (Trailblazer, Envoy, Rainier) in Cellular Communication.
  14. Install the right rear seat cushion. Refer to Seat Cushion Replacement - Rear No. 1 (TrailBlazer, Envoy, Rainier) in Seats.
  15. Arm the CTD system and check for proper operation. Refer to Content Theft Deterrent (CTD) Description and Operation .
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.