Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1722 (REAR WHEEL STEERING SYSTEM)SPECIFICATIONS
2004 Oldsmobile Bravada AWD
Section 1722 (Rear Wheel Steering System): Specifications
2004 Oldsmobile Bravada AWDSECTION Specifications
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2003 GMC Yukon XL, 2003 GMC Yukon, 2003 Chevrolet Tahoe, 2003 Chevrolet Suburban, and 2003 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
Fastener Tightening Specifications
| Application | Specification | |
|---|---|---|
| Metric | English | |
| Axle Bracket Retaining Bolts/Nuts | 25 N.m | 18 lb ft |
| Brake Hose Bracket Retaining Bolt | 12 N.m | 106 lb in |
| Control Module to Bracket | 25 N.m | 18 lb ft |
| Inner Tie Rod End Support Clamp | 25 N.m | 18 lb ft |
| Inner Tie Rod End to Steering Gear | 100 N.m | 74 lb ft |
| Inner Tie Rod Jam Nut | 65 N.m | 48 lb ft |
| Lower Ball Joint Pinch Bolt | 230 N.m | 169 lb ft |
| Lower Ball Joint Retaining Bolts | 110 N.m | 81 lb ft |
| Outer Tie Rod End Retaining Bracket Bolts | 65 N.m | 48 lb ft |
| Outer Tie Rod End Retaining Nut to Steering Knuckle | 55 N.m | 40 lb ft |
| Park Brake Cable Bracket Retaining Bolt | 65 N.m | 48 lb ft |
| Rear Wheel Position Sensor | 4 N.m | 35 lb in |
| Rear Wheel Steering Control Module Bracket to Frame Nuts | 25 N.m | 18 lb ft |
| Steering Gear Actuator and Cover Retaining Bolts | 61 N.m | 45 lb ft |
| Steering Gear Motor to the Steering Gear, 4 mm bolts | 4 N.m | 35 lb in |
| Steering Gear Motor to the Steering Gear, 6 mm bolts | 10 N.m | 89 lb in |
| Steering Gear Protection Shield Retaining Bolts | 180 N.m | 132 lb ft |
| Upper Ball Joint Retaining Bolts | 110 N.m | 81 lb ft |
| Upper Ball Joint Retaining Nut | 200 N.m | 147 lb ft |
| Wheel Hub and Bearing Retaining Bolts | 140 N.m | 103 lb ft |
| Wheel Drive Shaft Retaining Nut | 250 N.m | 184 lb ft |
| Yaw Rate Sensor/Lateral Accelerometer Sensor Nuts | 10 N.m | 89 lb in |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.