Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Torque Specifications: Notes
2004 Oldsmobile Bravada AWDSECTION Notes
WARNING: This page is about a different car, the 2002 GMC Savana and 2002 Chevrolet Chevy Express. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Component | Ft. Lbs. (N.m) | ||||||
|---|---|---|---|---|---|---|---|
| AFCM Bracket Battery Tray Bolt | 18 (24) | ||||||
| AFCM Bracket Fender Bolt | 18 (24) | ||||||
| Coolant Line Bracket Bolt | 21 (28) | ||||||
| Fill Line "O" Ring Face Seal Fitting | 27 (37) | ||||||
| Fill Valve Mounting Nut | 21 (28) | ||||||
| Fuel Control Solenoid (FCS) Elbow Fitting | (1) | ||||||
| Fuel Mixer Housing Bracket to A/C Bracket Bolt | 21 (28) | ||||||
| FTP Sensor | 27 (37) | ||||||
| HPL Fuel Inlet & Outlet Fitting | 27 (37) | ||||||
| HPL Plug Fitting | 27 (37) | ||||||
| HPL Solenoid | (2) 225 (305) | ||||||
| HPR Bracket Frame Bolt | 21 (28) | ||||||
| HPR Bracket Thru-Frame Bolt | 27 (37) | ||||||
| HPR Coolant Inlet and Outlet Fitting | (1) | ||||||
| HPR Fuel Inlet Fitting | 27 (37) | ||||||
| HPR Fuel Outlet Fitting | (1) | ||||||
| HPR Mounting Nut | 40 (54) | ||||||
| HPR Pressure Relief Device Fitting | (1) | ||||||
| Idle Control Solenoid (ICS) Elbow Fitting | (1) | ||||||
| LPL Fuel Inlet Fitting | (1) | ||||||
| Low Pressure Lock-Off Fuel Outlet Fitting | (1) | ||||||
| Low Pressure Regulator Mounting Bracket Intake Stud | 21 (28) | ||||||
| Low Pressure Regulator Elbow Fitting | (1) | ||||||
| Low Pressure Regulator Fuel Inlet Fitting | (1) | ||||||
| Low Pressure Regulator Fuel Outlet Fitting | (1) | ||||||
| Negative Battery Cable Bolt | 11 (15) | ||||||
| "O" Ring Face Seal Fuel Line Fitting | 27 (37) | ||||||
| Spare Tire Mounting Frame Bolt | 72 (100) | ||||||
| Spare Tire Mounting Wing Bolt | 6 (8) | ||||||
| Tank Mounting Frame Bolt | 72 (100) | ||||||
| Tank Mounting Frame Thru Front Vehicle Frame Bolt | 18 (24) | ||||||
| Tank Mounting Frame Thru Rear Vehicle Frame Bolt | 27 (37) | ||||||
| Tank Shield Mounting Bolt | 18 (24) | ||||||
| Tank Strap Mounting Nut and Bolt | (3) 35 (47) | ||||||
| Tank Support Backing Plate Nut | 16 (22) | ||||||
| Throttle Body Adaptor to Intake Stud Nut | 35 (4) | ||||||
| INCH Lbs. (N.m) | |||||||
| AFCM Bracket Support Rod Bolt | 106 (12) | ||||||
| AFCM Tray-To-Bracket Bolt | 106 (12) | ||||||
| Alternative Fuels Fuel Pump Relay Mounting Nut | 106 (12) | ||||||
| Alternative Fuels Relay Bracket-To-Front of Dash Nut | 106 (12) | ||||||
| Fill Valve Mounting Cup Bolt | 106 (12) | ||||||
| Fuel Control Solenoid Mounting Bolt | 106 (12) | ||||||
| Fuel Control Solenoid & Idle Control Solenoid Manifold-To-Low Pressure Regulator Bracket Bolt | 106 (12) | ||||||
| Fuel Mixer Housing Bracket Bolts | 106 (12) | ||||||
| Fuel Mixer-To-Throttle Body Adapter Mounting Bolt | 35 (4) | ||||||
| Fuel Mixer Housing-To-Throttle Body Adapter V-Clamp | 18 (2) | ||||||
| HPL Electrical Connector Bracket Bolt | 106 (12) | ||||||
| High Pressure Lock-Off Relay Mounting Nut | 106 (12) | ||||||
| Idle Control Solenoid Mounting Bolt | 106 (12) | ||||||
| Ignition Relay Mounting Nut | 106 (12) | ||||||
| LPL Solenoid-To-Bracket Bolt | 106 (12) | ||||||
| LPL Bracket-To-LPR Bracket Bolt | 106 (12) | ||||||
| LPR Mounting Bracket-To-Intake Manifold Nut | 106 (12) | ||||||
| LPR-To-Mounting Bracket Bolt | 106 (12) | ||||||
|
|||||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.