Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE2004BRAVADA AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 132 (ENGINE CONTROLS - REMOVAL & INSTALLATION, OVERHAUL)TORQUE SPECIFICATIONS
2004 Oldsmobile Bravada AWD
Torque Specifications
2004 Oldsmobile Bravada AWDSECTION Torque Specifications
WARNING: This page is about a different car, the 2002 Pontiac Grand Prix, 2002 Chevrolet Monte Carlo, 2002 Chevrolet Impala, 2002 Buick Regal, and 2002 Buick Century. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | |||
|---|---|---|---|---|
| AIR Pump Mounting Bracket Nuts (3.8L - Impala & Monte Carlo | 37 (50) | |||
| Bypass Valve Actuator Bolts (3.8L - VIN 1) | 18 (25) | |||
| Crankshaft Balancer Bolt | ||||
| 3.1L & 3.4L | 76 (103) | |||
| 3.8L | (1) 111 (150) | |||
| Crankshaft Position Sensor Studs (3.8L) | 22 (30) | |||
| EGR Valve Bolts/Nuts | 22 (30) | |||
| EGR Valve Inlet Pipe (3.8L) | 18 (25) | |||
| Bolt | 22 (30) | |||
| Stud | 37 (50) | |||
| EGR Valve Outlet Pipe Bolt/Nut (3.8L) | 22 (30) | |||
| EGR Valve Pipe Bolt/Nut (3.1L & 3.4L) | 18 (25) | |||
| Engine Coolant Temperature Sensor | 15 (20) | |||
| Engine Mount Strut Bolt (3.1L & 3.8L) | 35 (47) | |||
| Fender Brace Bolt | 35 (47) | |||
| Fuel Filter Mounting Bracket Bolt | 15 (20) | |||
| Fuel Filter Outlet Pipe Fitting | 22 (30) | |||
| Fuel Rail Studs (3.8L - VIN 1) | 18 (25) | |||
| Fuel Return Pipe Nut At Pressure Regulator (3.1L & 3.4L) | 13 (17) | |||
| Fuel Tank Strap Bolts | 35 (47) | |||
| Generator Brace Bolt/Nut (3.8L - VIN 1) | 37 (50) | |||
| Heated Oxygen Sensor | 31 (42) | |||
| Heater Pipe-To-Throttle Body Nut | 18 (25) | |||
| Knock Sensor | 14 (19) | |||
| Spark Plug | 11 (15) | |||
| Supercharger Bolts (3.8L - VIN 1) | 17 (23) | |||
| Throttle Body Nuts/Bolts (3.1L & 3.4L) | 21 (28) | |||
| Throttle Body Support Bracket Nuts (3.8L) | 12 (16) | |||
| Wheel Lug Nuts | 100 (140) | |||
| INCH Lbs. (N.m) | ||||
| AIR Pipe Nut (3.8L) | 89 (10.0) | |||
| AIR Pump Fasteners (3.8L) | 89 (10.0) | |||
| AIR Shut-Off Valve Bolt (3.8L) | 80 (9.0) | |||
| Camshaft Position Sensor | ||||
| 3.1L | 71 (8.0) | |||
| 3.4L & 3.8L | 89 (10.0) | |||
| Communications Interface Module Bracket Nuts | 35 (4.0) | |||
| Crankshaft Position Sensor Bolt (3.1L & 3.4L) | 89 (10.0) | |||
| Sensor "A" (24X) | 89 (10.0) | |||
| Sensor "B" (7X) | 97 (11.0) | |||
| EGR Heat Shield Bolt/Nut (3.8L - VIN 1) | 89 (10.0) | |||
| Front Fender Liner (3.8L - Impala & Monte Carlo) | ||||
| Stud Nut | 35 (4.0) | |||
| Screws | 18 (2.0) | |||
| To Rear Of Fender Bolt | 61 (7.0) | |||
| Fuel Filler Pipe-To-Under Body Screws | ||||
| 3.1L & 3.4L | 89 (10.0) | |||
| 3.8L | 18 (2.0) | |||
| Fuel Filler Pipe Hose Clamp | 22 (2.5) | |||
| Fuel Pressure Regulator Screw (3.1L & 3.4L) | 76 (8.5) | |||
| Fuel Rail Retaining Bolt/Nut | 89 (10.0) | |||
| Fuel Sender Access Panel Nuts | 89 (10.0) | |||
| Idle Air Control Valve | 27 (3.0) | |||
| Ignition Coil Screws | 40 (4.5) | |||
| Intake Air Duct Clamp | 18 (2.0) | |||
| Manifold Absolute Pressure Sensor Screws | ||||
| 3.1L & 3.4L | 27 (3.0) | |||
| 3.8L (VIN 1) | 44 (5.0) | |||
| MAF Sensor Screw (3.8L) | 27 (3.0) | |||
| PCM Connector Screws (3.1L) | 71 (8.0) | |||
| Throttle Body Nuts (3.8L) | 89 (10.0) | |||
| Throttle Position Sensor Screws | 18 (2.0) | |||
|
||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.