HVAC Component Views

2004 Oldsmobile Bravada AWDSECTION HVAC Component Views
WARNING: This page is about a different car, the 2002 Oldsmobile Bravada, 2002 GMC Envoy XL, 2002 GMC Envoy, and 2002 Chevrolet TrailBlazer. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Engine, Left Side
GM747710Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 A/C Compressor Clutch Connector
2 A/C Compressor
Fig 2: Body Front End
GM747711Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Ambient Air Temperature Sensor
Fig 3: A/C Refrigerant Pressure Sensor
GM797101Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Air Conditioning Refrigerant Pressure Sensor
2 A/C Compressor
Fig 4: Engine Compartment, Right Rear
GM747714Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 A/C Low Pressure Switch
Fig 5: Coolant Bypass Valve (Body Type VIN 6)
GM825659Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Accumulator
2 Coolant Bypass Valve
Fig 6: Instrument Panel Carrier
GM747715Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Blower
2 IP Center Support
3 Blower Motor Control Processor
4 Blower-Auxiliary
5 Air Temperature Actuator-Left
Fig 7: Instrument Panel Carrier-Right Side
GM747716Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Lower Air Temperature Sensor-Right
Fig 8: Instrument Panel Carrier-Center Section
GM747731Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Lower Air Temperature Sensor-Left
Fig 9: Instrument Panel Carrier, Left and Right
GM747718Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Air Temperature Actuator-Right
2 Air Temperature Actuator-Left
3 Defrost Actuator
4 Mode Actuator
Fig 10: Instrument Panel Carrier, Cowl Side
GM747719Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Recirculation Actuator
Fig 11: Instrument Panel Carrier-Air Duct
GM747721Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Upper Air Temperature Sensors
Fig 12: Instrument Panel
GM747798Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Ambient Light/Sunload Sensor
Fig 13: Instrument Panel, Center
GM747722Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 HVAC Control Module
Fig 14: Steering Wheel Controls
GM894975Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 HVAC Control Switch
2 Radio Control Switch
3 Driver Information Switch
4 Driver Information Switch-Fuel/Trip
Fig 15: Lower I/P, Right Side
GM891676Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Blower Motor Control Processor
2 Blower Motor
Fig 16: Front Auxiliary Blower Motor Switch (Body Type VIN 6)
GM826160Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Lower Console
2 Blower Motor Switch-Auxiliary
Fig 17: B-Pillar, Left
GM747723Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Inside Air Temperature Sensor
Fig 18: Lower Console
GM872448Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Lower Console
2 HVAC Control Module-Auxiliary or RSA/HVAC Control Module-Auxiliary
3 Console Mode Actuator
4 C309 (Body Type VIN 6)
5 C307
Fig 19: HVAC Module-Auxiliary (Body Type VIN 6)
GM872310Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Mode Actuator-Auxiliary
2 Blower-Auxiliary
3 Air Temperature Actuator-Auxiliary
4 C401
5 In-Line 30A Fuse
Fig 20: Blower Motor Control Processor-Auxiliary (Long Wheelbase, Body Type VIN 6)
GM1208964Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Body Rear Opening
2 Blower Motor Control Processor-Auxiliary
3 Rear Evaporator and Heater Core
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • You smell fuel, burning insulation, or see smoke.
  • Brakes feel soft, pull hard to one side, or make grinding noises.
  • The engine overheats, stalls repeatedly, or misfires under load.
  • You are missing required tools, torque specs, or safe lifting equipment.
  • You are not confident in the next step or safety outcome.