SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2025ROGUE ROCK CREEKREPAIR AND DIAGNOSISRESTRAINTSRESTRAINTS CONTROL SYSTEMSSRS AIR BAG CONTROL SYSTEMBASIC INSPECTIONDIAGNOSIS AND REPAIR WORK FLOWWORK FLOW
2025 Nissan-Datsun Rogue Rock Creek

Work Flow

2025 Nissan-Datsun Rogue Rock CreekSECTION Work Flow

OVERALL SEQUENCE 

GNSDB130638Courtesy of NISSAN NORTH AMERICA, INC.

DETAILED FLOW 

  1. GET INFORMATION FOR SYMPTOM 
    1. Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurs).
    2. Check operation condition of the function that is malfunctioning.

    >>

    GO TO 2.

  2. CHECK DTC 
    1. Check DTC.
    2. Perform the following procedure if DTC is detected.
      • Record DTC (Print them out using CONSULT).
      • Erase DTC.
      • Study the relationship between the cause detected by DTC and the symptom described by the customer.

    Are any symptoms described and any DTC detected?

    Symptom is described, DTC is detected>>

    GO TO 3.

    Symptom is described, DTC is not detected>>

    GO TO 4.

    Symptom is not described, DTC is detected>>

    GO TO 5.

  3. CONFIRM THE SYMPTOM 

    Try to confirm the symptom described by the customer. Verify relation between the symptom and the condition when the symptom is detected.

    >>

    GO TO 5.

  4. CONFIRM THE SYMPTOM 

    Try to confirm the symptom described by the customer. Verify relation between the symptom and the condition when the symptom is detected.

    >>

    GO TO 6.

  5. PERFORM DTC CONFIRMATION PROCEDURE 

    Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected again. Is DTC detected?

    YES>>

    GO TO 7.

    NO>>

    Check according to Intermittent Incident .

  6. DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS 

    Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom.

    >>

    GO TO 7.

  7. DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE 

    Inspect according to Diagnosis Procedure of the system. Is malfunctioning part detected?

    YES>>

    GO TO 8.

    NO>>

    Check according to Intermittent Incident .

  8. REPAIR OR REPLACE THE MALFUNCTIONING PART 
    1. Repair or replace the malfunctioning part.
    2. Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replacement.
    3. Check DTC. If DTC is detected, erase it.

    >>

    GO TO 9.

  9. FINAL CHECK 

    When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the malfunction is repaired securely. When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the symptom is not detected. Is DTC detected and does symptom remain?

    YES-1>>

    DTC is detected: GO TO 7.

    YES-2>>

    Symptom remains: GO TO 4.

    NO>>

    Before returning the vehicle to the customer, always erase DTC.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.