Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMITSUBISHI2005LANCER EVOLUTION L4-2.0L DOHC TURBOREPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSENGINEINTAKE MANIFOLDFASTENER TIGHTENING SPECIFICATIONS
2005 Mitsubishi Lancer Evolution L4-2.0L DOHC Turbo
Fastener Tightening Specifications
2005 Mitsubishi Lancer Evolution L4-2.0L DOHC TurboSECTION Fastener Tightening Specifications
INTAKE MANIFOLD
FASTENER TIGHTENING SPECIFICATIONS
ITEM SPECIFICATION
Center cover bolt 3.0 ± 0.5 Nm (27 ± 4 in-lb)
EGR vacuum regulator solenoid bolt 11 ± 1 Nm (98 ± 8 in-lb)
EGR valve bolt 20 ± 2 Nm (15 ± 1 ft-lb)
Evaporative emission purge solenoid bolt 11 ± 1 Nm (98 ± 8 in-lb)
Fuel high-pressure hose bolt 5.0 ± 1.0 Nm (44 ± 9 in-lb)
Fuel pressure solenoid bolt 11 ± 1 Nm (98 ± 8 in-lb)
Fuel rail bolt 11 ± 1 Nm (98 ± 8 in-lb)
Generator brace bolt 22 ± 1 Nm (98 ± 8 in-lb)
Ground cable bolt 5.0 ± 1.0 Nm (44 ± 9 in-lb)
Intake manifold bolt
M8 20 ± 2 Nm (15 ± 1 ft-lb)
M10 36 ± 6 Nm (27 ± 4 ft-lb)
Intake manifold nut 36 ± 6 Nm (27 ± 4 ft-lb)
Intake manifold stay bolt 31 ± 3 Nm (23 ± 2 ft-lb)
Manifold differential pressure sensor bolt 5.0 ± 1.0 Nm (44 ± 9 in-lb)
Oil level gauge guide bolt 13 ± 1 Nm (115 ± 9 in-lb)
Vacuum hose and pipe assembly bolt 11 ± 1 Nm (98 ± 8 in-lb)
FASTENER TIGHTENING SPECIFICATIONS
ITEM SPECIFICATION
Center cover bolt 3.0 ± 0.5 Nm (27 ± 4 in-lb)
EGR vacuum regulator solenoid bolt 11 ± 1 Nm (98 ± 8 in-lb)
EGR valve bolt 20 ± 2 Nm (15 ± 1 ft-lb)
Evaporative emission purge solenoid bolt 11 ± 1 Nm (98 ± 8 in-lb)
Fuel high-pressure hose bolt 5.0 ± 1.0 Nm (44 ± 9 in-lb)
Fuel pressure solenoid bolt 11 ± 1 Nm (98 ± 8 in-lb)
Fuel rail bolt 11 ± 1 Nm (98 ± 8 in-lb)
Generator brace bolt 22 ± 1 Nm (98 ± 8 in-lb)
Ground cable bolt 5.0 ± 1.0 Nm (44 ± 9 in-lb)
Intake manifold bolt
M8 20 ± 2 Nm (15 ± 1 ft-lb)
M10 36 ± 6 Nm (27 ± 4 ft-lb)
Intake manifold nut 36 ± 6 Nm (27 ± 4 ft-lb)
Intake manifold stay bolt 31 ± 3 Nm (23 ± 2 ft-lb)
Manifold differential pressure sensor bolt 5.0 ± 1.0 Nm (44 ± 9 in-lb)
Oil level gauge guide bolt 13 ± 1 Nm (115 ± 9 in-lb)
Vacuum hose and pipe assembly bolt 11 ± 1 Nm (98 ± 8 in-lb)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.