Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMITSUBISHI2005LANCER EVOLUTION L4-2.0L DOHC TURBOREPAIR AND DIAGNOSISHEATING AND AIR CONDITIONINGSPECIFICATIONSMECHANICAL SPECIFICATIONSFASTENER TIGHTENING SPECIFICATIONS
2005 Mitsubishi Lancer Evolution L4-2.0L DOHC Turbo
Fastener Tightening Specifications
2005 Mitsubishi Lancer Evolution L4-2.0L DOHC TurboSECTION Fastener Tightening Specifications
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATION
ITEM SPECIFICATION
Liquid pipe A mounting nut (condenser side) 4.9 ± 1.0 N.m (43 ± 8 in-lb)
Flexible discharge hose mounting nut (condenser side) 12 ± 2 N.m (107 ± 17 in-lb)
Flexible discharge hose mounting bolt (compressor side) 25 ± 4 N.m (18 ± 3 ft-lb)
Flexible suction hose mounting bolt (compressor side) 25 ± 4 N.m (18 ± 3 ft-lb)
Flexible suction hose mounting nut (suction pipe connection) 12 ± 2 N.m (107 ± 17 in-lb)
Suction pipe mounting bolt (heater unit side) 12 ± 2 N.m (107 ± 17 in-lb)
Liquid pipe A mounting nut (liquid pipe B connection) 13 ± 1 N.m (115 ± 9 in-lb)
Compressor clutch mounting nut 16 ± 1 N.m (12 ± 1 ft-lb)
FASTENER TIGHTENING SPECIFICATION
ITEM SPECIFICATION
Liquid pipe A mounting nut (condenser side) 4.9 ± 1.0 N.m (43 ± 8 in-lb)
Flexible discharge hose mounting nut (condenser side) 12 ± 2 N.m (107 ± 17 in-lb)
Flexible discharge hose mounting bolt (compressor side) 25 ± 4 N.m (18 ± 3 ft-lb)
Flexible suction hose mounting bolt (compressor side) 25 ± 4 N.m (18 ± 3 ft-lb)
Flexible suction hose mounting nut (suction pipe connection) 12 ± 2 N.m (107 ± 17 in-lb)
Suction pipe mounting bolt (heater unit side) 12 ± 2 N.m (107 ± 17 in-lb)
Liquid pipe A mounting nut (liquid pipe B connection) 13 ± 1 N.m (115 ± 9 in-lb)
Compressor clutch mounting nut 16 ± 1 N.m (12 ± 1 ft-lb)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.