Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMITSUBISHI2004GALANT V6-3.8L (6G75)REPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSAIR BAG SYSTEMSSYSTEM SPECIFICATIONS
2004 Mitsubishi Galant V6-3.8L (6G75)
System Specifications
2004 Mitsubishi Galant V6-3.8L (6G75)SECTION System Specifications
FASTENER TIGHTENING SPECIFICATIONS
ITEM SPECIFICATION
Air bag module(s) and clock spring
Steering wheel dynamic damper mouthing bolt 3.9 ± 0.9 Nm (35 ± 8 in-lb)
Steering wheel nut 41 ± 8 Nm (30 ± 6 ft-lb)
Clock spring screw 0.69 ± 0.15 Nm (6 ± 1 in-lb
Torx screw 9.0 ± 2.0 Nm (80 ± 17 in-lb)
Front impact sensor
Front impact sensor nut 7.5 ± 2.5 Nm (67 ± 22 in-lb)
Seat belts with pre-tensioner
Seat belt lower anchor bolt 44 ± 10 Nm (33 ± 7 ft-lb)
Seat belt shoulder anchor bolt 44 ± 10 Nm (33 ± 7 ft-lb)
Seat belt with pre-tensioner mounting bolt 44 ± 10 Nm (33 ± 7 ft-lb)
Seat slide sensor
Seat slide sensor mounting bolt 5.0 ± 1.0 Nm (44 ± 9 in-lb)
Side impact sensor
Side impact sensor nut 7.5 ± 2.5 Nm (67 ± 22 in-lb)
SRS control unit (SRS-ECU)
SRS-ECU mounting bolt 7.5 ± 2.5 Nm (67 ± 22 in-lb)
ITEM SPECIFICATION
Air bag module(s) and clock spring
Steering wheel dynamic damper mouthing bolt 3.9 ± 0.9 Nm (35 ± 8 in-lb)
Steering wheel nut 41 ± 8 Nm (30 ± 6 ft-lb)
Clock spring screw 0.69 ± 0.15 Nm (6 ± 1 in-lb
Torx screw 9.0 ± 2.0 Nm (80 ± 17 in-lb)
Front impact sensor
Front impact sensor nut 7.5 ± 2.5 Nm (67 ± 22 in-lb)
Seat belts with pre-tensioner
Seat belt lower anchor bolt 44 ± 10 Nm (33 ± 7 ft-lb)
Seat belt shoulder anchor bolt 44 ± 10 Nm (33 ± 7 ft-lb)
Seat belt with pre-tensioner mounting bolt 44 ± 10 Nm (33 ± 7 ft-lb)
Seat slide sensor
Seat slide sensor mounting bolt 5.0 ± 1.0 Nm (44 ± 9 in-lb)
Side impact sensor
Side impact sensor nut 7.5 ± 2.5 Nm (67 ± 22 in-lb)
SRS control unit (SRS-ECU)
SRS-ECU mounting bolt 7.5 ± 2.5 Nm (67 ± 22 in-lb)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.