Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMITSUBISHI2004ECLIPSE L4-2.4L SOHCREPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSFUEL DELIVERY AND AIR INDUCTIONSYSTEM SPECIFICATIONS
2004 Mitsubishi Eclipse L4-2.4L SOHC
System Specifications
2004 Mitsubishi Eclipse L4-2.4L SOHCSECTION System Specifications
FASTENER TIGHTENING SPECIFICATIONS
ITEM SPECIFICATION
Engine coolant temperature sensor 29 ± 10 Nm (22 ± 7 ft-lb)
Fuel high-pressure hose 4.9 ± 1.0 Nm (44 ± 8 in-lb)
Fuel pressure regulator 8.8 ± 1.0 Nm (78 ± 9in-lb)
Fuel rail mounting bolt 12 ± 1 Nm (100 ± 13 in-lb)
Idle air control motor 2.0 ± 0.5 Nm (18 ± 4 in-lb)
Lever assembly 4.9 ± 1 Nm (43 ± 9 in-lb)
Throttle body bracket M6 4.9 ± 1.0 Nm (43 ± 9 in-lb)
Throttle body bracket M8 6.9 ± 1.5 Nm (61 ± 13 in-lb)
Throttle body mounting bolt 19 ± 3 Nm (14 ± 2 ft-lb)
Throttle body stay mounting bolt 19 ± 3 Nm (14 ± 2 ft-lb)
Throttle position sensor 2.0 ± 0.5 Nm (18 ± 4 in-lb)
Throttle speed adjusting screw mounting nut 2.0 ± 0.5 Nm (18 ± 4 in-lb)
ITEM SPECIFICATION
Engine coolant temperature sensor 29 ± 10 Nm (22 ± 7 ft-lb)
Fuel high-pressure hose 4.9 ± 1.0 Nm (44 ± 8 in-lb)
Fuel pressure regulator 8.8 ± 1.0 Nm (78 ± 9in-lb)
Fuel rail mounting bolt 12 ± 1 Nm (100 ± 13 in-lb)
Idle air control motor 2.0 ± 0.5 Nm (18 ± 4 in-lb)
Lever assembly 4.9 ± 1 Nm (43 ± 9 in-lb)
Throttle body bracket M6 4.9 ± 1.0 Nm (43 ± 9 in-lb)
Throttle body bracket M8 6.9 ± 1.5 Nm (61 ± 13 in-lb)
Throttle body mounting bolt 19 ± 3 Nm (14 ± 2 ft-lb)
Throttle body stay mounting bolt 19 ± 3 Nm (14 ± 2 ft-lb)
Throttle position sensor 2.0 ± 0.5 Nm (18 ± 4 in-lb)
Throttle speed adjusting screw mounting nut 2.0 ± 0.5 Nm (18 ± 4 in-lb)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.