Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMITSUBISHI2004DIAMANTE V6-3.5L SOHCREPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSDISC BRAKE SYSTEMSYSTEM SPECIFICATIONS
2004 Mitsubishi Diamante V6-3.5L SOHC
System Specifications
2004 Mitsubishi Diamante V6-3.5L SOHCSECTION System Specifications
Front disc brake
Bleeding nipple 8 Nm (6 ft. lbs.)
Brake hose connection bolt 29 Nm (22 ft. lbs.)
Front brake assembly mounting bolt 90 Nm (65 ft. lbs.)
Lock pin 74 Nm (54 ft. lbs.)
Rear disc brake
Bleeding nipple 10 Nm (7 ft. lbs.)
Brake hose connection bolt 29 Nm (22 ft. lbs.)
Guide pin locking bolts 32 Nm (24 ft. lbs.)
Rear brake assembly mounting bolt 49 - 59 Nm (36 - 43 ft. lbs.)
Front disc brake pad thickness
Standard Value 10 mm (0.39 inch)
Limit 2.0 mm (0.08 inch)
Front disc brake drag force (tangential force of wheel mounting bolts) 69 mm (15.4 inch) or less
Front brake disc thickness
Standard Value 24 mm (0.94 inch)
Limit 22.4 mm (0.88 inch)
Front brake disc run-out Limit 0.05 mm (0.0020 inch)
Front hub end play 0.05 mm (0.0020 inch)
Rear disc brake pad thickness
Standard Value 8.8 mm (0.35 inch)
Limit 1.0 mm (0.039 inch)
Rear disc brake drag force (tangential force of wheel mounting bolts) 69 mm (15.4 inch) or less
Rear brake disc thickness
Standard Value 10.4 mm (0.41 inch)
Limit 8.4 mm (0.33 inch)
Rear brake disc run-out 0.06 mm (0.0023 inch)
Rear hub end play 0.05 mm (0.0020 inch)
Booster push rod to master cylinder piston clearance 9.2 - 9.4 mm (0.362 - 0.370 inch)
Bleeding nipple 8 Nm (6 ft. lbs.)
Brake hose connection bolt 29 Nm (22 ft. lbs.)
Front brake assembly mounting bolt 90 Nm (65 ft. lbs.)
Lock pin 74 Nm (54 ft. lbs.)
Rear disc brake
Bleeding nipple 10 Nm (7 ft. lbs.)
Brake hose connection bolt 29 Nm (22 ft. lbs.)
Guide pin locking bolts 32 Nm (24 ft. lbs.)
Rear brake assembly mounting bolt 49 - 59 Nm (36 - 43 ft. lbs.)
Front disc brake pad thickness
Standard Value 10 mm (0.39 inch)
Limit 2.0 mm (0.08 inch)
Front disc brake drag force (tangential force of wheel mounting bolts) 69 mm (15.4 inch) or less
Front brake disc thickness
Standard Value 24 mm (0.94 inch)
Limit 22.4 mm (0.88 inch)
Front brake disc run-out Limit 0.05 mm (0.0020 inch)
Front hub end play 0.05 mm (0.0020 inch)
Rear disc brake pad thickness
Standard Value 8.8 mm (0.35 inch)
Limit 1.0 mm (0.039 inch)
Rear disc brake drag force (tangential force of wheel mounting bolts) 69 mm (15.4 inch) or less
Rear brake disc thickness
Standard Value 10.4 mm (0.41 inch)
Limit 8.4 mm (0.33 inch)
Rear brake disc run-out 0.06 mm (0.0023 inch)
Rear hub end play 0.05 mm (0.0020 inch)
Booster push rod to master cylinder piston clearance 9.2 - 9.4 mm (0.362 - 0.370 inch)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.