Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMINI2013COOPER COUNTRYMAN, STANDARD TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 878 (GENERAL ELECTRICAL SYSTEM - REPAIR)
2013 Mini Cooper Countryman, Standard Trans
Section 878 (General Electrical System - Repair)
2013 Mini Cooper Countryman, Standard TransSECTION Section 878 (General Electrical System - Repair)
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2008 BMW Z4, 2007 BMW Z4, 2006 BMW Z4, 2005 BMW Z4, and 2004 BMW Z4. However, it is still accessible from the selected car via links, so may be relevant.
- Troubleshooting
- Wiring Harness
- Auxiliary Cable
- Plug Connection, Terminals
- 61 00... Notes on handling optical fibers
- 61 13 Special tools for wiring harness repairs
- 61 13.. Unlocking and disconnecting different plug connections
- 61 13... Base of tab connector housings
- 61 13... Antenna elbow plug on radio receiver
- 61 13... Crimping Micro Power Quadlock contacts (MPQ)
- 61 13... Crimping Micro Quadlock System contacts (MQS)
- 61 13... Crimping annular contacts
- 61 13... Crimping optical fibres
- 61 13... Cutting off, stripping insulation and cutting optical fibres to length
- 61 13... Opening plug housings and removing contacts of different plug systems
- 61 13... Plug housing, LCC contact (load current contact)
- 61 13... Relay carrier
- 61 13... Repairing ribbon cables
- 61 13... Retaining bracket
- 61 13... Socket housing (radio plug), Hybrid System MQS/MPQ
- Battery
- Battery/Vapor Separator
- Switch
- 61 31. Overview of switches
- 61 31.. Overview of switches in instrument panel/driver's footwell
- 61 31.. Overview of switches on center console or panel for storage box at rear
- 61 31 005 Removing and installing/replacing fixture for steering column stalk
- 61 31 016 Removing and installing/replacing turn indicator/headlight dipping switch
- 61 31 018 Removing and installing/replacing cruise control switch
- 61 31 020 Removing and installing/replacing ignition starter switch
- 61 31 033 Removing and installing/replacing light switch unit
- 61 31 040 Removing and installing/replacing switch for windshield wipers
- 61 31 056 Removing and installing/replacing shifters for SMG transmission
- 61 31 057 Removing and installing/replacing switch unit in center console
- 61 31 068 Removing and installing/replacing switch for passenger airbag deactivation
- 61 31 069 Removing and installing/replacing indicator for front passenger airbag deactivation
- 61 31 079 Removing and installing/replacing switch for hazard warning flashers/central locking
- 61 31 083 Removing and installing/replacing switch for unlocking rear lid
- 61 31 115 Replacing rocker switch for side-window operation
- 61 31 176 Removing and installing/replacing emergency call button
- 61 31 204 Replacing switch combination for seat adjustment
- 61 31 220 Removing and installing/replacing multifunction steering wheel switch
- 61 31 241 Removing and installing/replacing engine hood contact switch
- 61 31 255 Replacing switch for door mirror
- 61 31 270 Removing and installing/replacing switch for reversing light (DME)
- 61 31 287 Removing and installing/replacing driving dynamics switch
- 61 31 299 Removing and installing/replacing clutch switch module
- 61 31 310 Replacing brake light switch
- 61 31 345 Removing and installing/replacing microswitch for storage box lighting
- 61 31 382 Replacing Level Switch For Coolant
- 61 31 440 Removing and installing/replacing temperature switch for heated windshield spray jets
- 61 31 492 Replacing level switch for windshield washer system
- 61 31 798 Removing and installing/replacing sensor on left convertible top catch
- 61 31 799 Removing and installing/replacing microswitch convertible top compartment-
- 61 31 807 Replacing both sensors on left convertible top main bearing
- Steering Angle Sensor Adjustment
- Horn
- ECU Modules
- 61 35.. Overview of control units, modules
- 61 35... Notes on ESD protection (Electro Static Discharge)
- 61 35 070 Removing and installing/replacing module for folding door mirror
- 61 35 147 Removing and installing/replacing convertible top module
- 61 35 177 Removing and installing (replacing) rain/light sensor
- 61 35 622 Removing and installing/replacing general module
- 61 35 679 Initializing rain/light sensor
- 61 35 900 Removing and installing/replacing ring antenna of electronic immobilizer
- 61 35 910 Removing and installing/replacing control unit of electronic immobilizer
- Diagnosis Programming/Coding
- Relays
- Windshield Wipers
- 61 61... Overview of windshield washer system and headlight cleaning system (SRA)
- 61 61 010 Checking/adjusting approach angle of windshield wiper arms on front windscreen
- 61 61 041 Replacing Both Windshield Wiper Blades
- 61 61 100 Removing and installing/replacing both windshield wiper arms
- 61 61 270 Removing and installing/replacing bracket for windshield wiper system complete with motor
- Headlight Washer System
- 61 61... Overview of windshield washer system and headlight cleaning system (SRA)
- 61 67 010 Removing and installing/replacing washer pump of headlight cleaning system
- 61 67 040 Adjusting spray nozzles for headlight cleaning system
- 61 67 083 Removing and installing/replacing left or right high-pressure nozzle of headlight cleaning system
- Window Washer System
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.