Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMINI2013COOPER COUNTRYMAN, STANDARD TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 4394 (ENGINE ELECTRICAL SYSTEM - REPAIR - F33)
2013 Mini Cooper Countryman, Standard Trans
Section 4394 (Engine Electrical System - Repair - F33)
2013 Mini Cooper Countryman, Standard TransSECTION Section 4394 (Engine Electrical System - Repair - F33)
WARNING: This page does not describe the selected car, but rather 11 other vehicles, including the 2016 BMW 435i xDrive, 2016 BMW 435i, 2016 BMW 428i xDrive, 2016 BMW 428i, and 2015 BMW 435i xDrive. However, it is still accessible from the selected car via links, so may be relevant.
- General And Safety Information
- 00 Safety information for working on vehicles with automatic engine start-stop function (MSA)
- 11 00... Handling components after flood damage
- 61 00... Notes on handling wiring harnesses and cables
- 12 00... Instructions for working on the ignition system
- 12 00... Instructions for removal and replacement of control units
- 61 13... Notes for opening contacts and locks of different plug contact systems
- 61 20... Battery replacement information
- 61 00... Notes for disconnecting and connecting battery
- 12 00... Notes/information on start assistance (jump starting)
- 61 13... Butt connector for repairing a plug connection
- Ignition Wires, Spark Plugs
- Ignition Coil
- Electronic Switching Or Control Units
- 12 14 700 Coding control module (DME/DDE)
- 12 14 705 Programming control unit (DME/DDE)
- 12 14 602 Removing/re placing knock sensor (1st and 2nd cylinder) (N20, N26)
- 12 14 600 Removing/replacing knock sensor (3rd and 4th cylinder) (N20, N26)
- 12 14 600 Removing/replacing knock sensors (N55)
- 12 14 524 Replace pulse sensor on exhaust camshaft (N20, N26)
- 12 14 550 Replacing control unit (DME) (N20, N26)
- 12 14 550 Replacing control unit (DME) (N55)
- 12 14 521 Replacing crank shaft pulse sensor (N20, N26)
- 12 14 521 Replacing crank shaft pulse sensor (N55)
- 12 14 651 Replacing pressure sensor on charge air duct (N55)
- 12 14 650 Replacing pressure sensor on intake plenum (N55)
- 12 14 524 Replacing pulse sensor on exhaust camshaft (N55)
- 12 14 523 Replacing pulse sensor on in take camshaft (N20, N26)
- 12 14 523 Replacing pulse sensor on in take camshaft (N55)
- 12 14 650 Replacing suction pressure sensor on intake plenum (N20, N26)
- 12 14 650 Replacing suction pressure sensor on pressure pipe (N20, N26)
- 12 63 586 Replacing power distribution module (N20, N26, N55)
- Alternator With Drive And Mounting
- Controller
- Starter With Mounting
- Starter Lead
- 12 42 500 Replacing positive battery cable between starter motor, alternator and positive battery connect ion point (N55)
- 12 42 540 Replacing safety battery terminal (SBK)
- 12 42 500 Replacing the positive battery cable between the starter motor, alternator and positive battery connection point (N20, N26)
- Engine Wiring Loom
- 12 51 235 Removing and installing/replacing engine sensor system wiring harness module 1 (N20, N26)
- 12 51 240 Removing and installing/replacing engine wiring harness sensor system module 2 (N20, N26)
- 12 51 215 Replacing wiring harness section for Valvetronic servomotor (N20, N26)
- 12 51 001 Replacing wiring harness section for engine (N55)
- 12 51 245 Replacing wiring harness section for engine transmission module (N20, N26)
- 12 51 210 Replacing wiring harness section for ignition and injectors (N20, N26)
- 12 51 100 Replacing wiring harness section for ignition and injectors (N55)
- Oil Pressure/Oil Temperature/Oil Gauge
- 12 61 285 Removing and installing/renewing oil level sensor for engine oil (N55)
- 12 61 588 Removing and installing/replacing engine oil pressure/temperature sensor (N20, N26)
- 12 61 285 Removing and installing/replacing oil level sensor for engine oil (N20, N26)
- 12 61 280 Removing and installing/replacing oil pressure sensor (N55)
- Power Distribution Module
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.